--
-- Juniper Enterprise Specific MIB: SFF Digital Optical Monitor MIB
--
-- Copyright (c) 2010, Juniper Networks, Inc.
-- All rights reserved.
--
-- The contents of this document are subject to change without notice.
--
JUNIPER-DOM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32, NOTIFICATION-TYPE
FROM SNMPv2-SMI
DateAndTime, TEXTUAL-CONVENTION
FROM SNMPv2-TC
jnxDomMibRoot, jnxDomNotifications, jnxDomLaneNotifications
FROM JUNIPER-SMI
ifIndex, ifDescr
FROM IF-MIB;
-- DOM Alarm and Warning Type
jnxDomMib MODULE-IDENTITY
LAST-UPDATED "201403200000Z" -- Thu Mar 03 2009 UTC
ORGANIZATION "Juniper Networks, Inc."
CONTACT-INFO
" Juniper Technical Assistance Center
Juniper Networks, Inc.
1194 N. Mathilda Avenue
Sunnyvale, CA 94089
E-mail: support@juniper.net"
DESCRIPTION
"This MIB module defines objects used for Digital Optical
Monitor on interface of Juniper products."
REVISION "201403200000Z"
DESCRIPTION
"Change XFP references to generic SFF in descriptions. Add
DOM lane table."
REVISION "200912230000Z"
DESCRIPTION
"Initial revision."
::= { jnxDomMibRoot 1 }
JnxDomAlarmId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies specific DOM alarms that may exist on an
interface."
SYNTAX BITS {
domRxLossSignalAlarm(0), -- Input Loss of signal
domRxCDRLossLockAlarm(1), -- Input Loss of Lock
domRxNotReadyAlarm(2), -- Input rx path
domRxLaserPowerHighAlarm(3), -- Input laser power
domRxLaserPowerLowAlarm(4), -- Input laser power
domTxLaserBiasCurrentHighAlarm(5), -- Output laser bias current
domTxLaserBiasCurrentLowAlarm(6), -- Output laser bias current
domTxLaserOutputPowerHighAlarm(7), -- Output laser power
domTxLaserOutputPowerLowAlarm(8), -- Output laser power
domTxDataNotReadyAlarm(9), -- Output A/D data not ready
domTxNotReadyAlarm(10), -- Output tx path
domTxLaserFaultAlarm(11), -- Output laser safety
domTxCDRLossLockAlarm(12), -- Output CDR
domModuleTemperatureHighAlarm(13), -- Module temperature
domModuleTemperatureLowAlarm(14), -- Module temperature
domModuleNotReadyAlarm(15), -- Module MOD_NR
domModulePowerDownAlarm(16), -- Module P_DOWN
domLinkDownAlarm(17), -- Wire Unplugged or Down
domModuleRemovedAlarm(18), -- Module Unplugged or Down
domModuleVoltageHighAlarm(19), -- Module Voltage High
domModuleVoltageLowAlarm(20) -- Module Voltage Low
}
JnxDomWarningId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies specific DOM warnings that may exist on an
interface."
SYNTAX BITS {
domRxLaserPowerHighWarning(0), -- Input laser power
domRxLaserPowerLowWarning(1), -- Input laser power
domTxLaserBiasCurrentHighWarning(2), -- Output laser bias current
domTxLaserBiasCurrentLowWarning(3), -- Output laser bias current
domTxLaserOutputPowerHighWarning(4), -- Output laser power
domTxLaserOutputPowerLowWarning(5), -- Output laser power
domModuleTemperatureHighWarning(6), -- Module temperature
domModuleTemperatureLowWarning(7), -- Module temperature
domModuleVoltageHighWarning(8), -- Module voltage
domModuleVoltageLowWarning(9) -- Module voltage
}
JnxDomLaneAlarmId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies specific DOM alarms that may exist on
a Lane of a SFF interface"
SYNTAX BITS {
domLaneRxLaserPowerHighAlarm(0),
domLaneRxLaserPowerLowAlarm(1),
domLaneTxLaserBiasCurrentHighAlarm(2),
domLaneTxLaserBiasCurrentLowAlarm(3),
domLaneTxLaserOutputPowerHighAlarm(4),
domLaneTxLaserOutputPowerLowAlarm(5),
domLaneLaserTemperatureHighAlarm(6),
domLaneLaserTemperatureLowAlarm(7)
}
JnxDomLaneWarningId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies specific DOM warnings that may exist on
a Lane of a SFF interface"
SYNTAX BITS {
domLaneRxLaserPowerHighWarning(0),
domLaneRxLaserPowerLowWarning(1),
domLaneTxLaserBiasCurrentHighWarning(2),
domLaneTxLaserBiasCurrentLowWarning(3),
domLaneTxLaserOutputPowerHighWarning(4),
domLaneTxLaserOutputPowerLowWarning(5),
domLaneLaserTemperatureHighWarning(6),
domLaneLaserTemperatureLowWarning(7)
}
--
-- Current DOM Statistics
--
jnxDomDigitalMonitoring OBJECT IDENTIFIER ::= { jnxDomMib 1 }
jnxDomCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxDomCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about Digital Optical Monitoring for this
interfaces on this router."
::= { jnxDomDigitalMonitoring 1 }
jnxDomCurrentEntry OBJECT-TYPE
SYNTAX JnxDomCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about Digital Optical Monitoring
for this interfaces on this router."
INDEX { ifIndex }
::= { jnxDomCurrentTable 1 }
JnxDomCurrentEntry ::=
SEQUENCE {
jnxDomCurrentAlarms
JnxDomAlarmId,
jnxDomCurrentAlarmDate
DateAndTime,
jnxDomLastAlarms
JnxDomAlarmId,
jnxDomCurrentWarnings
JnxDomWarningId,
jnxDomCurrentRxLaserPower
Integer32,
jnxDomCurrentTxLaserBiasCurrent
Integer32,
jnxDomCurrentTxLaserOutputPower
Integer32,
jnxDomCurrentModuleTemperature
Integer32,
jnxDomCurrentRxLaserPowerHighAlarmThreshold
Integer32,
jnxDomCurrentRxLaserPowerLowAlarmThreshold
Integer32,
jnxDomCurrentRxLaserPowerHighWarningThreshold
Integer32,
jnxDomCurrentRxLaserPowerLowWarningThreshold
Integer32,
jnxDomCurrentTxLaserBiasCurrentHighAlarmThreshold
Integer32,
jnxDomCurrentTxLaserBiasCurrentLowAlarmThreshold
Integer32,
jnxDomCurrentTxLaserBiasCurrentHighWarningThreshold
Integer32,
jnxDomCurrentTxLaserBiasCurrentLowWarningThreshold
Integer32,
jnxDomCurrentTxLaserOutputPowerHighAlarmThreshold
Integer32,
jnxDomCurrentTxLaserOutputPowerLowAlarmThreshold
Integer32,
jnxDomCurrentTxLaserOutputPowerHighWarningThreshold
Integer32,
jnxDomCurrentTxLaserOutputPowerLowWarningThreshold
Integer32,
jnxDomCurrentModuleTemperatureHighAlarmThreshold
Integer32,
jnxDomCurrentModuleTemperatureLowAlarmThreshold
Integer32,
jnxDomCurrentModuleTemperatureHighWarningThreshold
Integer32,
jnxDomCurrentModuleTemperatureLowWarningThreshold
Integer32,
jnxDomCurrentModuleVoltage
Integer32,
jnxDomCurrentModuleVoltageHighAlarmThreshold
Integer32,
jnxDomCurrentModuleVoltageLowAlarmThreshold
Integer32,
jnxDomCurrentModuleVoltageHighWarningThreshold
Integer32,
jnxDomCurrentModuleVoltageLowWarningThreshold
Integer32,
jnxDomCurrentModuleLaneCount
Integer32
}
jnxDomCurrentAlarms OBJECT-TYPE
SYNTAX JnxDomAlarmId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies all the active DOM alarms
on a SFF physical interface on this router."
::= { jnxDomCurrentEntry 1 }
jnxDomCurrentAlarmDate OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The system date and time when the management subsystem learned
of the current alarm event."
::= { jnxDomCurrentEntry 2 }
jnxDomLastAlarms OBJECT-TYPE
SYNTAX JnxDomAlarmId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies a copy of jnxDomCurrentAlarms
before last set or clear."
::= { jnxDomCurrentEntry 3 }
jnxDomCurrentWarnings OBJECT-TYPE
SYNTAX JnxDomWarningId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies all the active DOM warnings
on a SFF physical interface on this router."
::= { jnxDomCurrentEntry 4 }
jnxDomCurrentRxLaserPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Receiver laser power."
::= { jnxDomCurrentEntry 5 }
jnxDomCurrentTxLaserBiasCurrent OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 mA"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Transmitter laser bias current."
::= { jnxDomCurrentEntry 6 }
jnxDomCurrentTxLaserOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Transmitter laser output power."
::= { jnxDomCurrentEntry 7 }
jnxDomCurrentModuleTemperature OBJECT-TYPE
SYNTAX Integer32
UNITS "Celsius (degrees C)"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Module temperature."
::= { jnxDomCurrentEntry 8 }
jnxDomCurrentRxLaserPowerHighAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Receiver laser power high alarm threshold."
::= { jnxDomCurrentEntry 9 }
jnxDomCurrentRxLaserPowerLowAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Receiver laser power low alarm threshold."
::= { jnxDomCurrentEntry 10 }
jnxDomCurrentRxLaserPowerHighWarningThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Receiver laser power high warning threshold."
::= { jnxDomCurrentEntry 11 }
jnxDomCurrentRxLaserPowerLowWarningThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Receiver laser power low warning threshold."
::= { jnxDomCurrentEntry 12 }
jnxDomCurrentTxLaserBiasCurrentHighAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 mA"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Transmitter laser bias current high alarm threshold."
::= { jnxDomCurrentEntry 13 }
jnxDomCurrentTxLaserBiasCurrentLowAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 mA"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Transmitter laser bias current low alarm threshold."
::= { jnxDomCurrentEntry 14 }
jnxDomCurrentTxLaserBiasCurrentHighWarningThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 mA"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Transmitter laser bias current high warning threshold."
::= { jnxDomCurrentEntry 15 }
jnxDomCurrentTxLaserBiasCurrentLowWarningThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 mA"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Transmitter laser bias current low warning threshold."
::= { jnxDomCurrentEntry 16 }
jnxDomCurrentTxLaserOutputPowerHighAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Transmitter laser power high alarm threshold."
::= { jnxDomCurrentEntry 17 }
jnxDomCurrentTxLaserOutputPowerLowAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Transmitter laser power low alarm threshold."
::= { jnxDomCurrentEntry 18 }
jnxDomCurrentTxLaserOutputPowerHighWarningThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Transmitter laser power high warning threshold."
::= { jnxDomCurrentEntry 19 }
jnxDomCurrentTxLaserOutputPowerLowWarningThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Transmitter laser power low warning threshold."
::= { jnxDomCurrentEntry 20 }
jnxDomCurrentModuleTemperatureHighAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "Celsius (degrees C)"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Module temperature high alarm threshold."
::= { jnxDomCurrentEntry 21 }
jnxDomCurrentModuleTemperatureLowAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "Celsius (degrees C)"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Module temperature low alarm threshold."
::= { jnxDomCurrentEntry 22 }
jnxDomCurrentModuleTemperatureHighWarningThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "Celsius (degrees C)"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Module temperature high warning threshold."
::= { jnxDomCurrentEntry 23 }
jnxDomCurrentModuleTemperatureLowWarningThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "Celsius (degrees C)"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Module temperature low warning threshold."
::= { jnxDomCurrentEntry 24 }
jnxDomCurrentModuleVoltage OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Module voltage."
::= { jnxDomCurrentEntry 25 }
jnxDomCurrentModuleVoltageHighAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Module voltage high alarm threshold."
::= { jnxDomCurrentEntry 26 }
jnxDomCurrentModuleVoltageLowAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Module voltage low alarm threshold."
::= { jnxDomCurrentEntry 27 }
jnxDomCurrentModuleVoltageHighWarningThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Module voltage high warning threshold."
::= { jnxDomCurrentEntry 28 }
jnxDomCurrentModuleVoltageLowWarningThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Module voltage low warning threshold."
::= { jnxDomCurrentEntry 29 }
jnxDomCurrentModuleLaneCount OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Number of Lanes (Lasers) in this module"
::= { jnxDomCurrentEntry 30 }
--
-- Current DOM Lane Statistics
--
jnxDomDigitalLaneMonitoring OBJECT IDENTIFIER ::= { jnxDomMib 2 }
jnxDomModuleLaneTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxDomCurrentLaneEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of information for this lane (Laser) of this
SFF optical module."
::= { jnxDomDigitalLaneMonitoring 1 }
jnxDomCurrentLaneEntry OBJECT-TYPE
SYNTAX JnxDomCurrentLaneEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about Digital Optical Monitoring for this
lane of this SFF optical Module"
INDEX { ifIndex, jnxDomLaneIndex }
::= { jnxDomModuleLaneTable 1 }
JnxDomCurrentLaneEntry ::=
SEQUENCE {
jnxDomLaneIndex
Integer32,
jnxDomCurrentLaneAlarms
JnxDomLaneAlarmId,
jnxDomCurrentLaneAlarmDate
DateAndTime,
jnxDomLaneLastAlarms
JnxDomLaneAlarmId,
jnxDomCurrentLaneWarnings
JnxDomLaneWarningId,
jnxDomCurrentLaneRxLaserPower
Integer32,
jnxDomCurrentLaneTxLaserBiasCurrent
Integer32,
jnxDomCurrentLaneTxLaserOutputPower
Integer32,
jnxDomCurrentLaneLaserTemperature
Integer32
}
jnxDomLaneIndex OBJECT-TYPE
SYNTAX Integer32 (0..1000)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A lane (Laser) on this SFF optical interface"
::= {jnxDomCurrentLaneEntry 1}
jnxDomCurrentLaneAlarms OBJECT-TYPE
SYNTAX JnxDomLaneAlarmId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies all the active DOM alarms
on a particular Lane of a SFF physical interface."
::= {jnxDomCurrentLaneEntry 2}
jnxDomCurrentLaneAlarmDate OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The system date and time when the management subsystem learned
of the current lane alarm event."
::= {jnxDomCurrentLaneEntry 3}
jnxDomLaneLastAlarms OBJECT-TYPE
SYNTAX JnxDomLaneAlarmId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies a copy of jnxDomCurrentAlarms
before last set or clear."
::= {jnxDomCurrentLaneEntry 4}
jnxDomCurrentLaneWarnings OBJECT-TYPE
SYNTAX JnxDomLaneWarningId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies all the active DOM warnings
on a particular Lane of a SFF physical interface."
::= {jnxDomCurrentLaneEntry 5}
jnxDomCurrentLaneRxLaserPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Receiver laser power on a particular Lane of a SFF
physcial interface."
::= {jnxDomCurrentLaneEntry 6}
jnxDomCurrentLaneTxLaserBiasCurrent OBJECT-TYPE
SYNTAX Integer32
UNITS "0.001 mA"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Transmitter laser bias on a particular Lane of a SFF
physcial interface."
::= {jnxDomCurrentLaneEntry 7}
jnxDomCurrentLaneTxLaserOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.01 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Transmitter laser power on a particular Lane of a SFF
physcial interface."
::= {jnxDomCurrentLaneEntry 8}
jnxDomCurrentLaneLaserTemperature OBJECT-TYPE
SYNTAX Integer32
UNITS "Celsius (degrees C)"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Temperature of laser on a particular Lane of a SFF
physcial interface."
::= {jnxDomCurrentLaneEntry 9}
--
-- Configuration Management Notifications
--
jnxDomNotificationPrefix OBJECT IDENTIFIER ::= { jnxDomNotifications 0 }
jnxDomAlarmSet NOTIFICATION-TYPE
OBJECTS { ifDescr,
jnxDomLastAlarms,
jnxDomCurrentAlarms,
jnxDomCurrentAlarmDate }
STATUS current
DESCRIPTION
"Notification of a recently set Dom alarm."
::= { jnxDomNotificationPrefix 1 }
jnxDomAlarmCleared NOTIFICATION-TYPE
OBJECTS { ifDescr,
jnxDomLastAlarms,
jnxDomCurrentAlarms,
jnxDomCurrentAlarmDate }
STATUS current
DESCRIPTION
"Notification of a recently cleared Dom alarm."
::= { jnxDomNotificationPrefix 2 }
jnxDomLaneNotificationPrefix OBJECT IDENTIFIER ::= { jnxDomLaneNotifications 0 }
jnxDomLaneAlarmSet NOTIFICATION-TYPE
OBJECTS { ifDescr,
jnxDomLaneIndex,
jnxDomLaneLastAlarms,
jnxDomCurrentLaneAlarms,
jnxDomCurrentLaneAlarmDate }
STATUS current
DESCRIPTION
"Notification of a recently set Dom Lane alarm."
::= { jnxDomLaneNotificationPrefix 1 }
jnxDomLaneAlarmCleared NOTIFICATION-TYPE
OBJECTS { ifDescr,
jnxDomLaneIndex,
jnxDomLaneLastAlarms,
jnxDomCurrentLaneAlarms,
jnxDomCurrentLaneAlarmDate }
STATUS current
DESCRIPTION
"Notification of a recently cleared Dom Lane alarm."
::= { jnxDomLaneNotificationPrefix 2 }
END