ON THIS PAGE
Creating a Full Mesh IP Service Order
You can use Connectivity Services Director application to implement IP services.
Creating an IP full mesh Ethernet service order consists of the following tasks:
Selecting the Service Definition
To select a service definition to base the new service order on:
- From the Connectivity Services Director application, select Service View from the Views list.
The workspaces that are applicable to routing and tunnel services are displayed.
- From the Junos Space user interface, click the Deploy tab in the Task Categories banner. The features that you can configure in this mode are displayed in the task pane.
- From the Service View pane, click the plus sign (+) to expand the tree and select the type of service.
- Click the plus sign (+) beside Connectivity to view services
based on protocols.
Expand the IP Services tree to select an IP service.
Expand the E-Line Services tree to select an E-Line service.
Expand the E-LAN Services tree to select an E-LAN service.
- Select IP Services and from the Tasks pane,
select Service Provisioning > Manage Services.
The Manage Network Services page is displayed in the top half of the right pane, which displays all of the configured services. The Manage Service Orders page is displayed in the bottom half of the right pane, which displays all of the service orders corresponding to a service.
- From the Manage Network Services page, select New > IP Service Order.
The Service Settings page in the Create IP Service Order wizard is displayed.
- From the Service Definition field, click Select to choose the service definition you want to base your
service order on.
The Choose Service Definition inventory page displays a view of only those published service definitions designed to work with the type of services you need.
Based on the fields or parameters that you defined in the service definition to be enabled for modification in the service order, the corresponding fields are available for editing. The fields that are disabled for modification in the service order can only be edited in the service definition.
- Select the check box beside the service definition that you want to associate with the service order, and click OK.
- (Optional) Select the Enable LSP Association check box to create or associate LSPs.
Select the Create LSP check box to import an existing LSP service definition and also select an LSP name pattern.
Note You can also create an LSP name pattern of your preference, instead of using an existing pre-defined pattern.
For information about creating an LSP name pattern, see Creating a Name Pattern for LSPs in the Service Order.
Select the Associate LSP check box to associate an existing LSP.
Configuring Service Parameters Information
In this topic you configure general settings, VPN settings that can be applied to all end points, and routing protocol settings for the provider edge (PE) and customer edge (CE) devices.
Specifying General Settings
To specify general information for an IP Service Order:
- Fill in the fields on the Service Settings page as indicated
in Table 1.
Table 1: IP Service Order - Service Settings
Field
Description
General Settings Name
Type a unique name for the service. The service order name can consist of only letters, numbers, and underscores.
Note: The name you specify for an IP Service Order becomes the routing-instance name in the device configuration when you deploy the service.
Comments
Type a description of the service.
Customer
Click Select to select name of the enterprise customer that requests for a service.
Click Clear to clear the current selection.
Service Definition
Click Select to choose a service definition from the Choose Service Definition pop-up.
The Service Order is created based on the service definition you choose.
Select the check box beside the service definition that you want to associate with the service order, and click OK.
Click View to view details of the service definition you selected.
The type of Service Definition you choose determines the fields that are available in the Connectivity Settings section, VPN Settings section, and the PE-CE Settings section of the Settings Page of the IP Service Order wizard.
Instance Type
The type of Service Definition you choose will determine the Instance Type displayed in the field.
Enable Distinct Instance Name
Select this check box to specify a distinct instance name for each device.
Note: Starting from Connectivity Services Director 2.0R4 onward, you can specify a distinct routing instance name for each device when you deploy a service on multiple devices while creating a full-mesh IP service order.
Connectivity Settings Policy Based Route Target
Select this check box to create a policy-based vrf instance.
Clear this check box to create a community-based vrf instance.
For more information on creating policies for an IP service, see Creating Policies for an IP Service.
Auto Pick Route Target
Clear this check box, to enable the Route Target field.
To override this setting in the service order, you can select the Editable in Service Order check box in the create Layer 3 full-mesh service definition wizard.
Route Target
Specify the route target range in any of the following formats:
AS Number format:
AS Number Range: 1 through 4294967295
IPv4 address format:
If AS Number or IP is less than or equal to 65535, range is 0 through 65535.
If AS Number or IP is greater than 65535, range is 0 through 4294967295.
Note: You must clear the Auto Pick Route Target check box to enable this field.
Note: Starting from Release 2.1R1 onward, Connectivity Services Director supports a mix of both 2-byte and 4-byte AS numbers while creating a full-mesh IP service order.
Auto Pick Hub Route Target
Select this check box to automatically generate a Hub Route Target.
Clear this check box to manually enter a Hub Route Target.
Note: The Auto Pick Hub Route Target check box is visible if the selected Instance Type is vrf.
You can edit this field if you select the Editable in Service Order check box in the Create Layer 3 Hub-and-Spoke Service Definition wizard.
Hub Route Target
Specify the hub route target range in any of the following formats:
prefix-number:assigned-number
Prefix-number can be any numeric value from 1 through 65535. Assigned-number can be any numeric value from 0 through 2147483647.
IPV4-address:assigned-number
IPV4-address can be any valid IPv4 address, and assigned-number can be any numeric value from 0 through 65635.
Note: To manually enter the Hub Route Target, clear the Auto Pick Hub Route Target check box.
Auto Pick Spoke Route Target
Select this check box to automatically generate a Spoke Route Target.
Clear the Auto Pick Spoke Route Target check box to manually enter a Spoke Route Target.
Note: The Auto Pick Spoke Route Target check box is visible only if Instance Type selected is vrf.
You can edit this field if you select the Editable in Service Order check box in the Create Layer 3 Hub-and-Spoke Service Definition wizard.
Spoke Route Target
Specify the spoke route target range in any of the following formats:
prefix-number:assigned-number
Prefix-number can be any numeric value from 1 through 65535. Assigned-number can be any numeric value from 0 through 2147483647.
IPV4-address:assigned-number
IPV4-address can be any valid IPv4 address, and assigned-number can be any numeric value from 0 through 65635.
VPN Settings VRF Table Label
Select this check box while creating a service definition to configure a separate label for each VRF to provide double lookup and egress filtering.
This check box is visible only if the selected Instance Type is vrf.
Export Direct Routes
Select this check box in the Create Layer 3 Full Mesh Service Definition wizard to export direct routes.
Enable Auto Export Routes
You can select this check box in the Create IP Service Definition wizard to enable internal and external route leak as part of route target creation.
Import Internal Routes
Select this check box in the Create IP Service Definition wizard to enable the internal route leak feature as part of route target policy creation.
Import External Routes
Select this check box in the Create IP Service Definition wizard to enable the external route leak feature as part of route target policy creation.
Enable MVPN
Select this check box to enable multicast VPN (MVPN) settings.
If you select this check box, the Enable MC-LAG check box is disabled.
Default UNI Settings MTU Factor
Specify a value for MTU Factor in the range 1 through 1087902. The default value for MTU Factor is 10.
The value you configure for MTU Factor should not exceed one tenth of the value you configured for burst size.
Note: This field is enabled only if you select MTU Based as the Burst Size.
Burst Period
Specify a value for Burst Period in the range 10 through 1000. The default value for Burst Period is 10.
Note: This field is enabled only when you select Line Rate Based as the Burst Size.
Specifying PE-CE Settings Information
You configure VPN attributes that are usually common for all the endpoints in the service. Depending on the service definition on which the service order is based, the values that you provide vary.
If you do not expect these attributes to be the same on all endpoints, you can set them to be the same for now and then make changes later, or you can skip this step and apply the attribute values one at a time later.
Fill in the PE-CE Settings as indicated in Table 2:
Table 2: Layer 3 VPN Service Order - PE-CE Settings
Field | Description |
---|---|
PE-CE Settings | |
Routing Protocol | The routing protocol in use is displayed. |
AS Overide | Select this check box to allow a service provisioner to override the AS number. This check box is available if you select BGP as the routing protocol while creating the service definition. |
Maximum Prefixes | Range: 1 through 4294967295 This feature limits the number of unique destinations in a routing instance. |
OSPF Domain ID |
This check box is available only if you select OSPF as the routing protocol while creating the service definition. |
OSPF Version | Choose an OSPF version from the OSPF Version list:
Junos OS supports OSPF version 2 (OSPFv2) and OSPF version 3 (OSPFv3). This check box is available only if OSPF is selected as the routing protocol while creating the service definition. |
Click Next
The Node Settings page appears.
Selecting N-PE Devices or Nodes
In this topic you select the N-PE devices that you want to host the service endpoints.
To select endpoint N-PE devices:
- Click Add in the Node Settings page
of the Create IP Service Order wizard to add a device.
A new row is added to the existing table.
Note You can create a new policy by clicking Create Policy.
This option is available if you select Policy Based Route Target check box and clear the Auto Pick Route Target check box.
For more information on creating a policy, see Creating Policies for an IP Service
- Click the arrow in the name field.
- From the list, select a device you want to add to the
service.
You can select more than one device.
- Click OK.
The device is added to the table.
Note You can modify the device settings by selecting the check box next to the device and clicking Edit.
Click Ok to save your changes.
Continue with modifying or entering the node parameters.
Setting Attributes for Endpoints or Nodes
For instructions on working with service templates in service orders, see Creating a Service Order Based on a Service Definition with a Template.
You set attributes for each endpoint in the service from the Node Settings page.
For each endpoint, the Node Settings page shows the value for each UNI attribute.
You can enter topology settings, create static routes on the service, and enter MVPN/PIM settings in the Node Settings page. To specify these settings for a CE device on the Node Settings page:
- Select the device and click Edit.
The Node Settings window appears.
- Fill in the fields to configure or change topology settings
as indicated in Table 3:
Table 3: IP Service Order - Topology Settings
Field
Description
Topology
The type of network circuit in use is displayed in this field:
Full Mesh
Hub-and-spoke
Is Stitching Point
Clear this check box.
If you select the Enable MC- LAG check box in the General Settings window, the Is Stitching Point check box is available for each endpoint. If you select the Is Stitching Point check box, all the parameters of that endpoint are disabled.
Is Hub
Select this check box to enable the node to function as a hub.
Clear this check box if you want the device to function as a spoke.
Note: This field is not applicable for full-mesh IP services.
Import RT Policy
Select a policy from the list.
Policies associated with other devices and policies created as part of the service are listed. You can select more than one policy.
You have the option to:
Select a policy from the list.
Clear the current selection by clicking Clear.
Note: You can also add or delete a policy while modifying the service.
Export RT Policy
Select a policy from the list
Policies associated with other devices and policies created as part of the service are listed. You can select more than one policy.
You have the option to:
Select a policy from the list.
Clear the current selection by clicking Clear.
Note: You can also add or delete a policy while modifying the service.
Auto pick Route Distinguisher
Select this check box to assign the Route Distinguisher automatically.
This field is enabled if you have selected the Editable in Service Order check box in the service definition.
Route Distinguisher
Enter a valid Route Distinguisher range:
as-number:id—Range: 1 through 65535
ip-address:id—Range:
ip address: any unique unicast address
id: 1 through 65535
Each routing instance must have a unique route distinguisher (RD) associated with it. The RD is used to place bounds around a VPN so that the same IP address prefixes can be used in different VPNs without any overlap.
This field is available only if you have selected full-mesh as the service type while creating the service definition.
Auto pick Hub Route Distinguisher
Select this check box to assign the Hub Route Distinguisher automatically.
This field is enabled if you selected the Editable in Service Order check box in the service definition.
Hub Route Distinguisher
Enter a valid Hub Route Distinguisher range:
as-number:id—Range: 1 through 65535
ip-address:id—Range:
ip address: any unique unicast address
id: 1 through 65535
This field is available only if you selected hub-and-spoke as the service type while creating the service definition.
Auto pick Spoke Route Distinguisher
Select this check box to assign the Spoke Route Distinguisher automatically.
This field is enabled only if you selected the Editable in Service Order check box in the service definition.
Spoke Route Distinguisher
Enter a valid Spoke Route Distinguisher range:
as-number:id—Range: 1 through 65535
ip-address:id—Range:
ip address: any globally unique unicast address
id: 1 through 65535
This field is available only if you selected hub-and-spoke as the service type while creating the service definition.
- Fill in the fields to create static routes on the service
as indicated in Table 4:
Table 4: IP Service Order - Static Routes
Field
Action
Destination Prefix
Enter the endpoint for the static route in this field.
IP address–Destination IP address that the router uses to identify packets.
Network mask–Network mask for associated IP subnet.
Netmask value: 0-32
Option Type
Choose an option type from the Option Type list:
next-hop
next-table
community
Note: Starting from Connectivity Services Director Release 2.1R1 onward, you can also configure static routes by adding next table and community as option types while creating a full-mesh IP service order.
Hop Address
Enter a valid IP address in this field. You can have multiple hop for every destination prefix.
This field is available only if you choose next-hop as the Option Type.
Route Table Name
Choose one of the following options as the route table name:
inet.0
inet.3
This field is available only if you choose next-table as the Option Type.
Member
Choose one of the following values as the member type:
no-export
no-advertise
no-export-subconfed
This field is available only if you choose community as the Option Type.
Add
Click Add to add a static route to the Static Route Table.
A new row is added to the table.
Delete
Select the row you want to delete and click Delete to remove the static route from the Static Route Table.
Attribute
The Attribute column displays the Option Type you select
Attribute Value
The Attribute Value column displays the corresponding value for every Option Type you select.
- Specify the MVPN and PIM Settings as indicated in Table 5:
Note The MVPN and PIM Settings sections are displayed only if you select the Enable MVPN check box in the Service Settings page of the Create IP Service Order wizard.
Table 5: IP Service Order - MVPN and PIM Settings
Field
Description
PIM Settings PIM Mode
Choose the PIM Mode from the drop down list.
Only sparse mode is currently supported.
MVPN Settings MVPN Mode
Choose one of the following MVPN modes from the MVPN Mode list:
rpt-spt
spt-only
Site Type
Choose one of the following MBGP MVPN site types from the list:
sender
receiver
Provider Tunnel Name
Specify the provider tunnel name to configure virtual private LAN service (VPLS) flooding of unknown unicast, broadcast, and multicast traffic using point-to- multipoint LSPs in this field. You can also configure point-to-multipoint LSPs for MBGP MVPNs.
Upstream Multicast Hop
Select this check box to configure the upstream multicast hop (UMH).
Import Target
Specify the import targets for sender and receiver sites in this field.
Select the Sender radio button to import targets for sender sites, select the Receiver radio button to import targets for receiver sites.
Import Unicast Target
Specify the import targets specifically for sender sites or receiver sites in this field. You can also borrow import targets from a configured unicast route target.
Note: A sender site export route target is always advertised when security association routes are exported. By default, the VPN routing and forwarding (VRF) import and export route targets (configured either using VRF import and export policies or using the vrf-target statement) are used for importing and exporting routes with the MBGP MVPN network layer reachability information (NLRI).
Export Unicast Target
Select this check box to specify the export target to enable you to override the Layer 3 VPN export route targets used for importing and exporting routes for the MBGP MVPN network layer reachability information (NLRI).
Auto pick Export Target
Select this check box to enable automatic selection of an export target if a configuration is not provided.
Target Community
Specify the target community value to be used when exporting sender and receiver site routes in this field.
You can specify this value manually if you clear the Autopick Export Target check box.
Click Ok to accept all configured values.
Click Cancel to reject all configured values.
- Click Next when you have finished configuring
node settings.
The Site Settings page is displayed.
Adding and Deleting UNI Interfaces
In the Site Settings page, you can add or delete UNI interfaces on the PE devices that participate in a service.
To add a UNI interface on a selected device:
Click Add to add a new row to the table.
From the newly added row, click the arrow in the Device Name field.
A list of interfaces is displayed.
Select the check boxes beside the UNIs that you want to associate with the service order and click Ok. You can select more than one UNI.
The table now displays the UNI interfaces configured on the selected device.
To delete a UNI Interface from a selected device, select the check box next to the interface that you want to delete, and click the Delete button above the table.
If the deleted UNI is the only UNI selected from the device, then the device is deleted from the service configuration.
Setting Attributes for UNIs or Sites
If there is a service template attached to the service definition, there is a link to that template at the bottom of the Site Settings section of the screen. For instructions on working with service templates in service orders, see Creating a Service Order Based on a Service Definition with a Template.
This part of the create Ethernet service order procedure sets the attributes for each endpoint in the service. Selection is made using the Site Settings page.
The interface shown in the UNI Interface field is automatically selected by the Connectivity Services Director application, which chooses the UNI that has the highest available capacity among interfaces that are in the Up state. To calculate the available capacity of the interface, the system subtracts the bandwidth reserved for each service deployed on that interface from the total capacity of the interface.
For each endpoint, the Site Settings page shows the value for each UNI attribute.
To modify the values of a UNI interface:
- To modify the device settings, select the device by clicking
the check box next to it.
The row is highlighted in blue.
- You can edit details in the row based on Table 6:
Table 6: IP Service Order - Modify or alter UNI Interface
Field
Description
Device Name
Displays the name of the device associated with the UNI.
Interface Name
Displays the selected interface name.
To add a new interface:
- Click the arrow in the Interface Name field.
- To select the interface, select the check box that corresponds to the interface.
- Click Ok.
The interface name is displayed and the corresponding fields are updated.
Interface Status
Displays the interface’s status.
A Green Up arrow indicates devices that are up and running.
A Red Down arrow indicates devices that are down.
Unit Autopick
Select this check box to assign the Unit ID automatically.
Clear this check box to assign the Unit ID manually.
Unit ID
Enter a value in this field.
Range: 1 through 1073741823
This field is available only if you clear the Unit Autopick checkbox.
VLAN Tagging
Select one of the following options from the list:
Port
Dot1Q
QinQ(All)
QinQ(Single)
Specifying the Dot1Q Ethernet option enables you to apply a Unit ID, a single VLAN ID, a VLAN Range, or a VLAN list to the service order.
Specifying the QinQ Ethernet option enables you to apply a single VLAN, a VLAN Range, or a VLAN list to the service order. For an IP service deployed on a dual tagged interface, the inner tag determines the VPN routing and forwarding instance(VRF).
VLAN Autopick
Select this check box to assign the VLAN Outer ID automatically.
Clear this check box to assign the VLAN Outer ID manually.
VLAN Outer
Enter a value in this field.
This field is available if you clear the Unit Autopick check box.
VLAN Inner
Enter a value in this field.
This field is available if you choose Dot1Q or QinQ(All) as the VLAN Tagging value.
IP Autopick
Select this check box to assign the IP address automatically.
Clear this check box to assign the IP address manually.
You cannot edit this check box if you have not selected the Editable in Service Order check box in the service definition.
IP Address
You can enter an IP address in this field if you have cleared the IP Autopick check box.
You can choose an IP address from the list if you have selected the IP Autopick check box.
IP Subnet
Enter a valid IP subnet in this field.
To configure or edit Site Settings:
- Select the interface that you want to edit by clicking
the check box next to it.
The selected row is highlighted in blue.
- You can edit the interface details by following Table 7:
Table 7: IP Service Order - Configure Site Settings
Field
Action
Site Settings Interface
The name of the interface you choose is displayed in this field.
Description
Type a description that describes the UNI Interface.
Range: 0 to 128 characters.
UNI Settings
Encapsulation
Choose an encapsulation value from the Encapsulation list:
Port
Dot1Q
QinQ(Single)
QinQ(All)
If you choose Port as the encapsulation value, no field in the UNI settings section is enabled.
If you choose Dot1Q as the encapsulation value, Auto pick Interface Unit and Auto pick VLAN ID check boxes are enabled.
If you choose QinQ(Single) or QinQ(All) as the encapsulation value, Customer VLAN Type and Outer TP ID fields are enabled.
Auto pick Interface Unit
Select this check box to automatically assign the Unit ID.
Clear this check box to manually enter the Unit ID.
Unit ID
Enter a unit ID in this field.
Range - 1 through 16385
This field becomes available when you clear the Auto pick Interface Unit check box.
Auto pick VLAN ID
Select this check box to assign the VLAN ID automatically.
Clear this check box to manually enter the VLAN ID.
VLAN ID
Enter a VLAN ID in this field.
Range - 1 through 4094
This field is available when you clear the Auto pick VLAN ID check box.
Customer VLAN Type
Choose a customer VLAN type from the Customer VLAN Type drop down box:
Transport All Traffic—Transports traffic from all VLANs across the network
Transport Single VLAN—Transports traffic for a specific VLAN across the network.
This field is available only when the encapsulation value you select is QinQ(Single) or QinQ(All)
Customer VLAN ID
Enter a Customer VLAN ID in this field.
Range - 1 through 4094
This field is available only when you select Transport Single VLAN as the Customer VLAN type.
Outer TP ID
Choose a value form the Outer TP ID list:
empty (default)
0x8100
0x88a8
0x9100
Inner TP ID
Choose a value form the Inner TP ID list:
empty (default)
0x8100
0x88a8
0x9100
This field is available when you select Transport Single VLAN as the customer VLAN type.
IP Settings Autopick Interface IP
Select this check box to choose an interface IP from IP Address Pool drop down list.
Clear this check box to manually enter an interface IP in the Interface IP Address field.
IP Pool Type
Displays the IP Pool Type you have selected.
Global
Customer
None
Interface IP Address
Enter an interface IP address.
This field is available only when you clear the Autopick Interface IP check box.
IP Address Pool
Choose an interface IP address from the IP Address Pool drop down list.
This field is available only if you select the Autopick Interface IP check box.
IP Block size
Enter a valid IP address block size value in this field.
Range - 1 through 32
Note: Starting from Connectivity Services Director Release 2.1R1 onward, you can configure an IP block size using a wider range from 1 through 32 while creating a full-mesh IP service order.
PE-CE Settings Routing Protocol
Select a protocol from the list:
BGP
OSPF
Static
OSPF Area ID
Enter an OSPF area id.
Valid IP Range - 0.0.0.0 through 255.255.255.255
This field is available only if OSPF is selected as the routing protocol in the service definition.
OSPF Version
Enter an OSPF version number.
Ver 2
Ver 3
This field is available only if OSPF is selected as the routing protocol in the service definition.
Group Name
Enter a group name.
Range - 0 to 255 characters
This field is available only if BGP is selected as the routing protocol in the service definition.
Local Address
This field is available if BGP is selected as the routing protocol in the service definition.
Autopick Neighbour IP
Select this field if you want to automatically generate a Neighbour IP. You can edit this field if you select Editable in Service Order check box.
This field is available only if BGP is selected as the routing protocol in the service definition.
Neighbour IP
Enter a vaild IP address in this field.
Range - 1.0.0.1 through 223.225.225.254, excluding 127.x.x.x
This field is available if BGP is selected as the routing protocol in the service definition.
Peer AS
Enter a Peer AS range in this field.
Range - 1 through 4294967295
This field is available if BGP is selected as the routing protocol in the service definition.
Import Policy
Select the policy from the list.
Policies associated with other devices and policies created as part of the service is listed. You can select more than one policy from the list.
You also have the option to:
Select a policy from the list.
Clear the current selection by clicking Clear.
You can also add or delete a policy while modifying the service.
Export Policy
Select the policy from the list.
Policies associated with other devices and policies created as part of the service is listed. You can select more than one policy from the list.
Select a policy from the list.
Clear the current selection by clicking Clear.
You can add or delete a policy while modifying the service.
PIM Settings Add
Click Add to add a new row in the PIM Settings table.
Delete
Click Delete to delete a row from the PIM Settings table.
Rendezvous Point (device)
Click the arrow in this field to select a device from the drop down list.
Group Address
Enter a group IP address.
Range - 224.0.1.0 through 239.255.255.255
Update or Cancel
Click Update to update the Rendezvous Point (device) and Group Address to the PIM Settings table.
Click Cancel to cancel any updates.
- Click Ok after you enter the site settings
details in the Site Settings window.
The site settings page is displayed.
- Click Next.
The Review page is displayed.
You can examine and modify the created service order parameters. Alternatively, you can click the corresponding buttons at the top of the wizard page to navigate to the specific pages.
- Click Done. The Confirmation dialogue
box appears.
You can choose one of the following options:
Save & Validate
Save & Deploy
- Click Ok to confirm the deployment option.
Specifying QoS Settings
CoS profiles enable the grouping of class-of-service (CoS) parameters and apply them to one or more interfaces. Connectivity Services Director provides you with predefined traffic types for each CoS profile that you create. These traffic types represent the most common types of traffic for the device type. Each of these templates has preconfigured values for all CoS parameters based on the typical application requirements. You can change the preconfigured values of these parameters to suit your requirements. To display the CoS Profiles page, in Build mode, select CoS under Profile and Configuration Management in the Tasks pane. The Manage CoS Profiles page appears.
If QoS is enabled on the service definition, configure the QoS Settings of the Site Settings panel of the service order creation wizard.
- In the QoS profile field, select
a profile from the list.
The QoS profile list displays the QoS profiles that are currently configured in the Manage CoS Profiles page of the Connectivity Services Director application.
A QoS profile classifies traffic into defined service groups to provide the special treatment of traffic across the network service.
Specifying Template Settings
The Template Settings page of the service order creation and modification wizards enables you to associate service templates with an E-Line, E-LAN, and IP service order. You can apply only the templates that are previously configured in a service definition with the corresponding service order. The Template Settings page is available in the service order wizard only if the service definition that you selected to apply to the service order contains a service template. Otherwise, the Template Settings page is not displayed in the service order wizard. You can perform template operations for all endpoints in a service order.
If you defined a service template as the default service template, it is attached to the endpoint by default. You have the flexibility to create and provision a dynamic attribute in a service template. You can mark an attribute of a service template as dynamic, and you can obtain the values for these dynamic attributes from a specific device. To create a dynamic attribute, you must first mark an attribute of a service template as dynamic and then specify the device XPath for the dynamic attribute.
The Template Settings page is displayed before the Review page, which is the final step of the service order wizard.
In the Service Settings page of the Select Service Definition field of the service order creation wizard, you can double-click a service definition name displayed in the table to view the details of the definition in a popup dialog box. You can use this information to determine if the service definition is appropriate for your deployment needs. To filter and sort the display of service templates, enter the name of the template as a match criterion in the Search box and click the Search icon. The page refreshes to display only the template names that match with the search term. You can use the paging controls to navigate across multiple pages of templates as necessary.
All the tasks that you can perform with service templates are presented in the Template Settings page. The page is divided into three panes. The top half of the page displays a table of selected endpoints. All the endpoints or UNIs that you selected in the preceding pages of the service order wizard are displayed in this table. You can configure the template pertaining to only one endpoint at a point in time. If the selected endpoints (in previous pages of the wizard) contained a manually-entered unit number, that number is displayed in the table of selected endpoints. Otherwise, the Auto-pick label is displayed.
The lower half of the page is divided into two panes. The left pane displays the template selection table for the endpoint you selected. All the templates associated with the service definition are displayed. You can add and delete templates using the template selection table. The right pane displays all the parameters that you can modify for a selected service template. All such editable parameters are displayed in a consolidated form of a configuration page. This pane is displayed after you select a template. If any configuration parameter in template is set as a service-specific value, such attributes are not displayed in this pane.
To associate a service template with a service order:
- Click Add to include a service template for
the endpoint. A dialog box is displayed with the list of service templates
associated with the service definition that is used to create the
service order. The templates selected in this dialog box are displayed
in the Template Selection table for the specified endpoint. Such templates
are considered to be attached to that endpoint.
If you specified a template as a default template during the service definition creation, the template is displayed by default in the template selection table. You can associate non-default templates with the service order by clicking the Add button.
- Click the link in the template name to open the Template Details dialog box. The template settings are displayed in the popup dialog box. For the selected template, the Configuration Page is displayed in the lower-right pane of the Template Settings page.
- Modify any template-specific service components as necessary.
- Click Save to submit the changes.
- Select a template from the Template Selection table, and click Delete to remove the template from being associated with the service order for a particular endpoint.
Reviewing the Configured Settings
You can examine and modify the created service order parameters in the Review page of the Create IP Service Order wizard.
If you want to modify a particular section in the review page, click the Edit button corresponding to that section.
Click Done to save the service order. The Confirmation dialogue box appears.
Deploying the New Service
From the Confirmation dialogue box that appears, you can choose one of the following options to deploy the service:
Choose Save & Validate to validate the service.
Choose Save & Deploy to deploy the service immediately.
The service order is now complete.