Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation

Check for T3 Interface Error Statistics

Purpose

Persistent interface error statistics indicate that you need to open a case with JTAC.

Action

To check the local interface for error statistics, use the following Junos OS CLI operational mode command:

user@host> show interfaces t3-fpc/pic/port extensive

Sample Output

user@router> show interfaces t3-1/0/0 extensive
Physical interface: t3-1/0/0, Enabled, Physical link is Down
  Interface index: 9, SNMP ifIndex: 10
  Link-level type: Cisco-HDLC, MTU: 4474, Clocking: Internal
  Speed: T3, Loopback: None, CRC: 16, Mode: C/Bit parity
  Device flags   : Present Running Down
  Interface flags: Hardware-Down Link-Layer-Down Point-To-Point SNMP-Traps
  Link flags     : Keepalives
  Keepalive statistics:
    Input : 116 (last seen 00:02:59 ago)
    Output: 187 (last seen 00:00:09 ago)
  Statistics last cleared: Never
  Traffic statistics:
   Input  bytes  :                 2552                    0 bps
   Output bytes  :                 3703                    0 bps
   Input  packets:                  116                    0 pps
   Output packets:                  161                    0 pps
   Input errors :
    Errors: 0, Drops: 0, Framing errors: 229, Policed discards: 1
    L3 incompletes: 0, L2 channel errors: 0, L2 mismatch timeouts: 0
    SRAM errors: 0, HS link CRC errors: 0
  Output errors:
    Carrier transitions: 4, Errors: 0, Drops: 0, Aged packets: 0
   Active alarms  : LOF, LOS
   Active defects  : LOF, LOS
   DS3 Media :            Seconds        Count  State
    PLL Lock                  0            0  OK
    Reframing               273            2  Defect Active
    AIS                       0            0  OK
    LOF                     273            2  Defect Active
    LOS                     273            2  Defect Active
    IDLE                      0            0  OK
    YELLOW                    0            0  OK
    BPV                       0            0
    EXZ                       0            0
    LCV                     275     18022125
    PCV                       0            0
    CCV                       0            0
    LES                     275
    PES                     273
    PSES                    273
    CES                     273
    CSES                    273
    SEFS                    273
    UAS                     277
  HDLC configuration:
    Policing bucket: Disabled
    Shaping bucket : Disabled
    Giant threshold: 4484, Runt threshold: 3
  DSU configuration:
    Compatibility mode: None, Scrambling: Disabled, Subrate: Disabled
    FEAC loopback: Inactive, Response: Disabled, Count: 0
    BERT time period: 10 seconds, Elapsed: 0 seconds
    Algorithm: 2^3 - 1, Pseudorandom (1), Error rate: 10e-0
  PFE configuration:
    Destination slot: 1, Stream number: 0, PLP byte: 1 (0x00)
    COS transmit queue bandwidth:
      Queue0: 95, Queue1: 0, Queue2: 0, Queue3: 5
    COS weighted round robin:
      Queue0: 95, Queue1: 0, Queue2: 0, Queue3: 5
  Logical interface t3-1/0/0.0 (Index 12) (SNMP ifIndex 32)
    Flags: Device-down Point-To-Point SNMP-Traps, Encapsulation: Cisco-HDLC
    Protocol inet, MTU: 4470, Flags: None
      Addresses, Flags: Dest-route-down Is-Preferred Is-Primary
        Destination: 1.1.1.0/30, Local: 1.1.1.1, Broadcast: Unspecified

Meaning

Check for any error statistics that may appear in the output. There should not be any input or output errors. If there are any persistent input or output errors, open a case with JTAC at support@juniper.net, or at 1-888-314-JTAC (within the United States) or 1-408-745-9500 (from outside the United States).

Published: 2012-12-10

Published: 2012-12-10