SRX380 Power System
SRX380 Firewall Power Supply
You can install two power supplies in the slots located at the rear of the chassis. Each power supply provides an output power of 600 W. The SRX380 ships with one power supply installed.
Figure 1 shows the power supply for the SRX380.
The power supplies in the SRX380 Firewall are hot-insertable and hot-removable field-replaceable units (FRUs). You can replace them without powering off the device. If only one power supply is installed in your device, you need to power off the device before removing the power supply.
Table 1 lists the power consumed by the SRX380. The maximum power available on a PoE port is 30 W.
Device |
Number of PoE-Enabled Ports |
Maximum Power Consumed by the Device |
Maximum System Power Available for PoE |
|---|---|---|---|
SRX380 |
16 |
|
|
AC Power Supply LEDs on SRX380 Services Gateways
Each power supply has two LEDs on the faceplate that indicate the status of the power supply. Table 2 describes the AC power supply LEDs.
LED |
Color |
Description |
|---|---|---|
AC OK |
Off |
No AC power input. |
Red |
Power supply failure. |
|
Green |
The power supply is delivering power and is functioning correctly. |
|
DC OK |
Off |
No AC power input |
Red |
Power supply failure. |
|
Green |
The power supply is delivering power and is functioning correctly. |
Power Specifications for SRX380 Services Gateways
Table 3 provides the AC power supply electrical specifications for SRX380 devices.
Power Requirement |
Specification |
|---|---|
AC input voltage |
100 to 240 VAC |
AC input line frequency |
50 Hz/60 Hz nominal |
AC system current rating |
8.5 A at 100 VAC 4.25 A at 240 VAC |
Maximum AC inrush current |
11 A at 220 V/50 Hz (with four Mini-PIMs installed) |
AC Power Cord Specifications for SRX380
A detachable AC power cord is supplied with the AC power supplies. The coupler is type C13 as described by International Electrotechnical Commission (IEC) standard 60320. The plug end of the power cord fits into the power source outlet that is standard for your geographical location.
The AC power cord provided with each power supply is intended for use with that power supply only and not for any other use.
In North America, AC power cords must not exceed 4.5 meters (approximately 14.75 feet) in length, to comply with National Electrical Code (NEC) Sections 400-8 (NFPA 75, 5-2.2) and 210-52 and Canadian Electrical Code (CEC) Section 4-010(3). The cords supplied with the device are in compliance.
Table 4 lists the AC power cord specifications for the countries and regions listed in the table.
Country/Region |
Electrical Specifications |
Plug Standards |
Juniper Model Number |
|---|---|---|---|
Argentina |
250 VAC, 10 A, 50 Hz |
IRAM 2073 Type RA/3 |
CBL-EX-PWR-C13-AR |
Australia |
250 VAC, 10 A, 50 Hz |
AS/NZZS 3112 Type SAA/3 |
CBL-EX-PWR-C13-AU |
Brazil |
250 VAC, 10 A, 50 Hz |
NBR 14136 Type BR/3 |
CBL-EX-PWR-C13-BR |
China |
250 VAC, 10 A, 50 Hz |
GB 1002-1996 Type PRC/3 |
CBL-EX-PWR-C13-CH |
Europe (except Italy, Switzerland, and United Kingdom) |
250 VAC, 10 A, 50 Hz |
CEE (7) VII Type VIIG |
CBL-EX-PWR-C13-EU |
India |
250 VAC, 10 A, 50 Hz |
IS 1293 Type IND/3 |
CBL-EX-PWR-C13-IN |
Israel |
250 VAC, 10 A, 50 Hz |
SI 32/1971 Type IL/3G |
CBL-EX-PWR-C13-IL |
Italy |
250 VAC, 10 A, 50 Hz |
CEI 23-16 Type I/3G |
CBL-EX-PWR-C13-IT |
Japan |
125 VAC, 12 A, 50 Hz or 60 Hz |
JIS 8303 |
CBL-EX-PWR-C13-JP |
Korea |
250 VAC, 10 A, 50 Hz or 60 Hz |
CEE (7) VII Type VIIGK |
CBL-EX-PWR-C13-KR |
North America |
125 VAC, 13 A, 60 Hz |
NEMA 5-15 Type N5-15 |
CBL-EX-PWR-C13-US |
South Africa |
250 VAC, 10 A, 50 Hz |
SABS 164/1:1992 Type ZA/13 |
CBL-EX-PWR-C13-SA |
Switzerland |
250 VAC, 10 A, 50 Hz |
SEV 6534-2 Type 12G |
CBL-EX-PWR-C13-SZ |
Taiwan |
125 VAC, 13 A, 60 Hz |
NEMA 5-15 Type N5-15 |
CBL-EX-PWR-C13-US |
United Kingdom |
250 VAC, 10 A, 50 Hz |
BS 1363/A Type BS89/13 |
CBL-EX-PWR-C13-UK |
Figure 2 illustrates the plug on the power cord for some of the countries or regions listed in Table 4.
