100-Gigabit Ethernet PIC with CFP2 (PTX Series)

Software Release

PTX5000: Junos OS Release 14.1 and later

Hardware Features

Four 100-Gigabit Ethernet ports
Model number: P2-100GE-CFP2
Name in the CLI: 4x100GE CFP2
Power requirements: 1.66A@ –48 V (90W)
Large maximum transmission units (MTUs): up to 9500 bytes

Software Features

100-Gigabit Ethernet PIC with CFP2 (PTX Series) shows the first supported release for each software feature.

Table 1: Software Features Supported
Software Feature	PTX5000 First Supported Junos OS Release
Flexible-ethernet-services encapsulation	14.1
Flexible VLAN tagging	14.1
IFINFO / IFMON	14.1
IEEE 802.1 ag OAM	14.1
IEEE 802.3 ah OAM	14.1
IEEE 802.3ad link aggregation	14.1
Interrupt-driven link-down detection for MPLS FRR	14.1
MAC accounting per logical interface for source addresses	14.1
MAC filter per port for destination addresses and source addresses	14.1
MAC filter per logical interface for source addresses	14.1
SNMP	14.1
Up to 4000 logical interfaces share across all ports on a single PFE	14.1

Cables and Connectors

The following transceivers are supported on this PIC:

CFP2-100G-LR4-D—Supports 100GBASE-LR4
- Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications
- Connector: LC
CFP2-100G-SR10-D—Supports 100GBASE-SR10
- Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications
- Connector: 24-fiber MPO
CFP2-100GBASE-LR4—Supports 100GBASE-LR4
- Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications
- Connector: LC
CFP2-100GBASE-SR10—Supports 100GBASE-SR10
- Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications
- Connector: 24-fiber MPO

Note:

The dual-rate transceiver (CFP2-100G-LR4-D) cannot be configured to use OTN framing when used in this PIC. The 100-Gigabit Ethernet OTN PIC with CFP2 (P2-100GE-OTN) supports OTN framing.

LEDs

The STATUS LED is located to the left of the ONLINE/OFFLINE button. One LED is located next to each port to indicate the link activity of the port. 100-Gigabit Ethernet PIC with CFP2 (PTX Series) describes the functions of these LEDs.

Table 2: 100-Gigabit Ethernet PIC with CFP2 LEDs
Label	Color	State	Description
STATUS	Green	On steadily	PIC is online with no alarms or failures.
	Yellow	On steadily	PIC is initializing.
	Red	On steadily	PIC has an error or failure.
	–	Off	PIC is offline or not enabled and safe to remove from the router.
Single LED per port	Green	On steadily	Port is online with no alarms or errors, and the link is up.
	Green	Blinking	There is link activity on the port.
	Red	On steadily	Port is on but the link is down, and the port has detected a failure.
	–	Off	Port is off or not enabled.

Alarms, Errors, and Events

Laser bias current high/low alarms and warnings
Laser Rx power high/low alarms and warnings
Module not ready alarm
Module low power alarm
Module temperature high/low alarms and warnings
Rx CDR loss of lock alarm
Rx loss of signal alarm
Module not ready alarm
Tx CDR loss of lock alarm

ON THIS PAGE