Creating a Point-to-Multipoint E-LAN Service Definition

in the Network Services > Connectivity view pane, select Service Design > Manage Service Definitions > New > E-LAN Service Definition. The General settings window appears.

To specify the general information for a point-to-multipoint service definition:

1. Fill in the fields on the General page of the wizard that enablesy ou to create a service definition.

   Field	Action
   Service Definition Name	Type a name for the service definition.
   Service Type	Select (E-LAN) Point-to-Multipoint )
   Signaling Protocol	Select a signaling type: BGP— If BGP signaling is selected, the following fields are available in the Connectivity section of the General Settings page: Route target Route distinguisher VLAN normalization MAC Settings VCID, if Enable PW Extension is enabled LDP—If LDP signaling is selected, the following fields are available in the Connectivity section of the General Settings page: Enable BGP-based Auto Discovery Auto-pick Route target, if Auto Discovery is enabled Auto-pick Route distinguisher, if Auto Discovery is enabled Auto-pick VPLS ID, if Auto Discovery is disabled Auto-pick VPN ID, if Auto Discovery is enabled VLAN normalization Mac Security Settings Note: You cannot edit the Signaling type in the service order.
   Description (Optional)	Type a brief description or other comment that you want to appear in the Service Definition table. Range: 0 through 200 characters. Space and special characters are allowed.
   Instance Type	Select an instance type to choose the type of routing instance for the Point-to-MultiPoint E-LAN service: vpls evpn virtual-switch
   Protocol	Different protocols are available based on the instance type you select: vpls evpn evpn e-tree
   Enable QoS	When you enable QoS in the service definition, you can specify a QoS profile in the service order to classify traffic into defined service groups to provide the special treatment of traffic across the network service. For example, voice traffic can be sent across certain links, and data traffic can use other links.
   Enable L3 Access	Select this check box to create the link into Layer 3. If this check box is selected, the available Ethernet option in the Site Settings window are: dot1q qinq
   Enable PW Extension	Select this check box to enable pseudowire extension. You cannot edit this check box in the service order.
   Enable PW Resiliency	Select this check box to enable resiliency. You cannot edit this field in the service order. If the Signaling type is BGP, you need to select the Enable PW Extension check box to enable the Enable PW Resiliency check box. For more information of pseudowire redundancy, see Redundant Pseudowires for Layer 2 Circuits and VPLS.
   Enable Static PW Labels	Select this check box to enable a pseudowire connection by configuring static values. Note: The Enable Static PW Labels check box is enabled for both signaling types: LDP and BGP. When the signaling type is BGP, selection of this check box enables the Enable PW Resiliency check box and automatically selects the Enable PW Extension check box.
   Service Template	(Optional) To include a service template for the service, click the Add icon or plus sign (+) to select a service template from the Service Template list. The list of available service templates is displayed. Select the check box beside the template you want and click OK. You are returned to the General Settings page. The selected service template appears in the Default Service Template field. You can select one or more service templates as the default service template. By default, the default service templates are attached to the endpoints. Note: You cannot add or delete a service template while creating a service order. The remaining service templates on the Service Template list are termed as optional service templates. You can attach the optional service templates to the endpoints on a need basis. In the View Service Definition Details window, the value for the default service template in the Default Service Template column is True. For instructions on creating a service template, see Creating a Service Template.
   BGP Connectivity Settings—This section is displayed if you select the signaling type as BGP.
   Auto-pick Route Target	Select this check box to enable route target to be configued automatically. Clear the check box if you want the route target to be manually configured. By default, manual configuration of route target is enabled. To override this setting in the service order, select the Editable in Service Order check box.
   Auto-pick Route Distinguisher	Define a route distinguisher option: Select the check box to enable the service provider to specify the route distinguisher. Select the check box to enable the route distinguisher to be selected automatically. To override this setting in the service order, select the Editable in Service Order check box.
   Enable Multihoming	Select this check box to pair any two N-PE devices, for providing redundant connectivity. When you select this check box, a Multihoming Mode list appears, if you select evpn or evpn-etree as the protocol type. You can select either single-active or all-active as the multihoming mode.
   LDP Connectivity Settings—This section is displayed if you select the signaling type as LDP.
   Enable BGP-based Auto Discovery	You cannot enable or disable the Auto Discovery check box if you have enabled the Enable PW Extension or the Enable PW Resiliency check boxes. This check box is available only if the signaling type is LDP. Note: If the Enable Static PW Labels check box in the General window is checked for the LDP signaling, then the Auto Discovery check box is disabled in the Connectivity Settings page. The Auto Discovery check box is not available in the Connectivity Settings page when the signaling type is BGP. On enabling the auto discovery, the following fields are available: Route target Route distinguisher VPN ID On disabling the auto discovery specify the VPLS ID.
   Auto-pick VPLS ID or VPN ID	This field is available only if the signaling type is LDP and auto discovery is disabled. Identifies the virtual circuit identifier used for the VPLS routing instance and the VPN ID associated with the router. Select this check box to enable the VPLS ID and VPN ID to be configued automatically. Clear the check box if you want these attributes to be manually configured. By default, manual configuration is enabled.
   Auto-pick Route Target	Select this check box to enable route target to be configued automatically. Clear the check box if you want the route target to be manually configured. By default, manual configuration of route target is enabled.
   Auto-pick Route Distinguisher	Define a route distinguisher option: Select the check box to enable the service provider to specify the route distinguisher. Select the check box to enable the route distinguisher to be selected automatically. To override this setting in the service order, select the Editable in Service Order check box.
   MAC Settings
   MAC learning	To enable MAC learning, select the check box.
   Interface MAC limit	Maximum number of MAC addresses learned from an interface. Range: 1 through 131071 MAC addresses per interface
   MAC statistics	To enable MAC statistic, select the check box.
   MAC Table Size	Modify the size of the MAC address table for the bridge domain. Range: 16 through 1048575 To allow the service provisioner to override the MAC settings, select Editable in Service Order.
   Enable L3 Access	Select this check box to create the link into Layer 3. If you enable the Layer 3 access, the available Ethernet option in the Site Settings are: port-port dot1q qinq asymmetric tag depth
   Enable PW Extension	Select this check box to enable pseudowire extension. You cannot edit this check box in the service order.
   Enable PW Resiliency	Select this check box to enable resiliency. You cannot edit this field in the service order. If the Signaling type is BGP, you need to select the Enable PW Extension check box to enable the Enable PW Resiliency check box. For more information of pseudowire redundancy, see Redundant Pseudowires for Layer 2 Circuits and VPLS.
   Enable Static PW Labels	Select this check box to enable a pseudowire connection by configuring static values. Note: The Enable Static PW Labels check box is enabled for both signaling types: LDP and BGP. When the signaling type is BGP, selection of this check box enables the Enable PW Resiliency check box and automatically selects the Enable PW Extension check box.
   Service Template Definition	(Optional) To include a service template for the service, click the Add icon or plus sign (+) to select a service template from the Service Template list. The list of available service templates is displayed. Select the check box beside the template you want and click OK. You are returned to the General Settings page. The selected service template appears in the Default Service Template field. You can select one or more service templates as the default service template. By default, the default service templates are attached to the endpoints. Note: You cannot add or delete a service template while creating a service order. The remaining service templates on the Service Template list are termed as optional service templates. You can attach the optional service templates to the endpoints on a need basis. In the View Service Definition Details window, the value for the default service template in the Default Service Template column is True. For instructions on creating a service template, see Creating a Service Template.

2. Click Next to save the information. Continue with Specifying Advanced Settings.

The Site Settings window provides four expanding or collapsing panels: Traffic Treatment, Interface Settings, MTU Settings, and Bandwidth Settings.

To specify the UNI Settings for Port-to-Port interfaces:

1. Fill in the fields on the Site Settings window.

   Field	Action
   PE-CE Interface Settings- Ethernet Encapsulation
   VLAN Tagging	Select port-port from the list. The VLAN tagging option you choose determines the other options you can select and specify on the page.
   Editable in Service Order	To allow the service provisioner to override the VLAN tagging or Ethernet option attribute, select the check box.
   LDP PW Extension Settings Note: The LDP PW Extension Settings is available only if you have selected the Enable PW Extension check box in the General tab.
   Physical Interface Encapsulation	In the Physical Interface Encapsulation box, select ethernet-ccc, which is the only valid physical interface encapsulation method for port-to-port services.
   Logical Interface Encapsulation	You can not select a choice in this field because it is not relevant to port-to-port services.
   Traffic Type	This drop-down is disabled for port-to-port services. For port-to-port services, all traffic is always transported.
   VLAN Normalization	Select a value: Normalize to vlan all—To preserve customer VLAN IDs (and customer QoS priorities) across the network. Note: For services that transport a range of VLANs, you must select VLAN Normalization to all. You cannot transport a range of VLANs without normalization. Normalize to vlan none—To preserve no VLAN IDs across the network. Normalize to Dot1q tag—To transport only single-tagged frames across the network core. All port, dot1q , and Q-in-Q traffic is transported across the network Normalize to QinQ tags—To transport only double-tagged frames across the network core. All port, dot1q , and Q-in-Q traffic is transported across the network. Normalization not required—To specify no normalization for port-to-port services Note: Starting with Release 1.0R2, when you newly install Connectivity Services Director, if you select the option to not require normalization in a service definition, the auto-pick option for VLAN IDs and the option to edit the auto-pick behavior in service order are disabled in the service definition. When you create a service order by associating with that service definition, you need to manually enter the VLAN IDs for the interfaces and cannot use the auto-pick functionality. This same behavior also applies to default service templates in which if you select the normalization-not-required functionality, the auto-pick option for VLAN IDs is disabled. For more information about VLAN normalization, see Junos Space Layer 2 Services Overview. For information about VLAN manipulation, see Understanding VLAN Manipulation (Normalization and VLAN Mapping) on Ethernet Services.
   Auto Pick VLAN ID	This check box is disabled because in port-to-port services, all traffic and all VLANs on one port are transported to all other ports.
   Editable in Service Order	To allow the service provisioner to override the VLAN ID setting, select the check box. This check box is not applicable for port-to-port services.
   Default Interface MTU (Bytes)	The default MTU value is 1522 bytes.
   MTU Range for manual-config(Bytes)	Specify the low and high values to define the MTU range that you want to define. The default range is 1522 through 9192 bytes.
   PE-CE Interface Rate-Limiting Settings
   Enable Interface Rate Limiting	To enable a service provisioner to limit the available bandwidth, select this check box, and type a default bandwidth limit. Note: Bandwidth settings are available in the service definition when Manage CoS Profiles page is configured with CoS profiles.
   Default bandwidth (Mbps)	Specify the default bandwidth value in Mbps. Default: 10 Mbps Range: 1 Mbps through 100,000 Mbps
   Min Bandwidth (Kbps)	Specify the minimum bandwidth value in Kbps. Default: 1000 Kbps Range: 64 Kbps through 100,000 Kbps
   Max Bandwidth (Mbps)	Specify the maximum bandwidth value in Mbps. For more information on maximum bandwidth see Table 1 Default: 100 Mbps Range: 1 Mbps through 100,000 Mbps
   Increment (Kbps)	Specify a value that defines which values in the range is made available to the service provisioner. Default: 1000 Kbps Range: 64 Kbps through 100,000 Kbps
   Bandwidth – Burst Size Settings
   Burst Size Calculator	Select the preferred option for calculating the burst size: MTU Based If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902. The default value for MTU Factor is 10. Burst Period Based If you select the option Burst Period Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds. The default value for Burst Period is 1. Note: The Burst Size Calculator list is enabled only when you select the Enable Interface Rate Limiting check box.

   The following table lists the Max Bandwidth (Mbps) for the M Series, MX Series, and ACX Series Routers:

   Table 1: Maximum Bandwidth for M Series, MX Series, and ACX Series Routers

   M Series IQ2E PIC		M Series IQ2 PIC		MX Series 3D PIC		MX Series Non-3D PIC		ACX 2000
   GE Port (1G)	XE Port (10G)	GE Port (1G)	XE Port (10G)	GE Port (1G)	XE Port (10G)	GE Port (1G)	XE Port (10G)	GE Port (1G)	XE Port (10G)
   32,000 Mbps or 32 Gbps	32,000 Mbps or 32 Gbps	50,000 Kbps or 50 Gbps	50,000 Kbps or 50 Gbps	100,000 Mbps or 100 Gbps	100,000 Mbps or 100 Gbps	50,000 Kbps or 50 Gbps	50,000 Kbps or 50 Gbps	50,000 Kbps or 50 Gbps	50,000 Kbps or 50 Gbps

2. Click Review to view the defined parameters. You can examine and modify the created service order parameters. Alternatively, click the corresponding buttons at the top of the wizard page to navigate to the specific pages pertain to the settings you want to modify. Click Back to return to the previous page of the wizard; else click Cancel to discard the changes.

   After you complete reviewing the settings, click Finish to complete the service definition creation.

To specify the UNI Settings for 802.1Q interfaces:

1. Fill in the fields on the Site Settings window.

   Field	Action
   PE-CE UNI Settings- Ethernet Encapsulation
   VLAN Tagging	Select dot1q from the list. The Ethernet option you choose determines the other options you can select and specify on the page.
   Physical Interface Encapsulation	In the Physical Interface Encapsulation box, select the default physical encapsulation scheme to be used by service orders based on this service definition. For point-to-multipoint services with 802.1Q interfaces, the only option is flexible-ethernet-services.
   Logical Interface Encapsulation	The Logical Interface Encapsulation field is constrained by your selection in the Physical Interface Encapsulation field. For the physical encapsulation mode of flexible-ethernet-services, your only option is to select vlan-vpls for the logical encapsulation method.
   LDP PW Extension Settings Note: The LDP PW Extension Settings is available only if you have selected the Enable PW Extension check box in the General tab.
   Physical Interface Encapsulation	In the Physical Interface Encapsulation box, select one of the following options: vlan-ccc extended-vlan-ccc flexible-ethernet-services
   Logical Interface Encapsulation	The Logical Interface Encapsulation field is constrained by your selection in the Physical Interface Encapsulation field. For the physical encapsulation mode of vlan-ccc or flexible-ethernet-services, your only option is to select vlan-ccc for the logical encapsulation method. For the physical encapsulation mode of extended-vlan-ccc, your only option is to select extended-vlan-ccc for the logical encapsulation method.
   Traffic Type	Select Transport single vlan to transport the traffic for a specific VLAN across the network. When you select this option, the service provisioner is prompted for the VLAN-ID when creating a service order based on this service definition. You need to specify the Outer Tag protocol ID. Select Transport vlan range to limit the traffic across the network to a specific range of VLANs. If you select this option, the service provisioner is prompted for the VLAN-ID range when creating a service order based on this service definition. Select Transport vlan list to limit the traffic across the network to a specific list of VLANs. If you select this option, the service provisioner is prompted for the VLAN-ID list when creating a service order based on this service definition. Note: Make sure to select Editable in Service Order if you want the service provisioner to be able to override this setting.
   VLAN Normalization	Select a value: Normalize to vlan all—To preserve customer VLAN IDs (and customer QoS priorities) across the network. Note: For services that transport a range of VLANs, you must select VLAN Normalization to all. You cannot transport a range of VLANs without normalization. Normalize to vlan none—To preserve no VLAN IDs across the network. Normalize to Dot1q tag—To transport only single-tagged frames across the network core. All port, dot1q , and Q-in-Q traffic is transported across the network Normalize to QinQ tags—To transport only double-tagged frames across the network core. All port, dot1q , and Q-in-Q traffic is transported across the network. Normalization not required—To specify no normalization for port-to-port services Note: Starting with Release 1.0R2, when you newly install Connectivity Services Director, if you select the option to not require normalization in a service definition, the auto-pick option for VLAN IDs and the option to edit the auto-pick behavior in service order are disabled in the service definition. When you create a service order by associating with that service definition, you need to manually enter the VLAN IDs for the interfaces and cannot use the auto-pick functionality. This same behavior also applies to default service templates in which if you select the normalization-not-required functionality, the auto-pick option for VLAN IDs is disabled. For more information about VLAN normalization, see Junos Space Layer 2 Services Overview. For information about VLAN manipulation, see Understanding VLAN Manipulation (Normalization and VLAN Mapping) on Ethernet Services.
   Auto Pick VLAN ID	Indicate how the VLAN ID is determined. By default, this check box is disabled. Clear this check box to allow the service provider to specify the VLAN ID. This option is normally used when no VLAN normalization is applied. Specify the VLAN ID range in VLAN range for manual input. Note: Make sure to select Editable in Service Order if you want the service provisioner to be able to override this setting. Select this check box when VLAN normalization is applied. Specify the VLAN ID pool in VLAN range for auto-pick. Note: Make sure to select Editable in Service Order if you want the service provisioner to be able to override this setting. Note: When the range of VLAN IDs that are automatically assigned by the system (with the auto-pick option enabled during the creation of a service definition) is less than or greater than the range of VLAN IDs that are manually specified (with the manual selection option enabled during the creation of a service definition), the following conditions apply during the creation of a service order with the Editable in Service Order check box selected during service definition creation: If you create a service order with the auto-pick option enabled, the VLAN ID is selected from the auto-pick range, and the value is displayed in the VLAN range for manual input field. If you attempt to change the VLAN ID manually, the value is restricted to the manually configured range. If you create a service order with the auto-pick option disabled, the VLAN ID is selected from the manually configured range, and the value is displayed in the VLAN range for manual input field. If you attempt to change the VLAN ID manually, the value is restricted to the manually configured range.
   VLAN range for auto-pick	Specify the VLAN ID pool. Range: 1 through 4094
   VLAN range for manual input	Specify the VLAN ID range. Range: 1 through 4094
   Outer Tag Protocol ID	Select the outer tag protocol ID if the Customer traffic type is Transport single VLAN: 0x88a8 0x8100 0x9100 Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPID) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100. To configure the TPIDs manually, use the following commands: set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x9100 set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x88a8 set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x8100
   Editable in Service Order	To allow the service provisioner to override the outer tag protocol ID setting, select the check box for those options.
   Default Interface MTU (Bytes)	The default MTU value is 1522 bytes. To allow the service provisioner to override the MTU setting, select the Editable in Service Order check box.
   MTU range for manual-config	In the MTU range fields, type the lowest and highest values for MTU for each UNI. Note: To allow the service provisioner to override the MTU setting, select Editable in Service Order and, in the MTU range fields, type the highest and lowest MTU values.
   PE-CE Interface Rate-Limiting Settings
   Enable Interface Rate Limiting	To enable a service provisioner to limit the available bandwidth, select this check box, and type a default bandwidth limit. Note: Bandwidth settings are available in the service definition when Manage CoS Profiles page is configured with CoS profiles.
   Default bandwidth (Mbps)	Specify the default bandwidth value in Mbps. Default: 10 Mbps Range: 1 Mbps through 100,000 Mbps
   Min Bandwidth (Kbps)	Specify the minimum bandwidth value in Kbps. Default: 1000 Kbps Range: 64 Kbps through 100,000 Kbps
   Max Bandwidth (Mbps)	Specify the maximum bandwidth value in Mbps. For more information on maximum bandwidth see Table 1 Default: 100 Mbps Range: 1 Mbps through 100,000 Mbps
   Increment (Kbps)	Specify a value that defines which values in the range is made available to the service provisioner. Default: 1000 Kbps Range: 64 Kbps through 100,000 Kbps
   Bandwidth – Burst Size Settings
   Burst Size Calculator	Select the preferred option for calculating the burst size: MTU Based If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902. The default value for MTU Factor is 10. Burst Period Based If you select the option Burst Period Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds. The default value for Burst Period is 1. Note: The Burst Size Calculator list is enabled only when you select the Enable Interface Rate Limiting check box.

2. Click Review to view the defined parameters. You can examine and modify the created service order parameters. Alternatively, click the corresponding buttons at the top of the wizard page to navigate to the specific pages pertain to the settings you want to modify. Click Back to return to the previous page of the wizard; else click Cancel to discard the changes.

   After you complete reviewing the settings, click Finish to complete the service definition creation.

To specify the UNI Settings for q-in-q interfaces:

1. Fill in the fields on the Site Settings window.

   Field	Action
   PE-CE Interface Settings- Ethernet Encapsulation
   VLAN Tagging	Select qinq from the list. The window expands to include options specific to Q-in-Q interfaces
   Physical Interface Encapsulation	In the Physical Interface Encapsulation box, select the default physical encapsulation scheme to be used by service orders based on this service definition. For point-to-multipoint services with 802.1Q interfaces, the only option is flexible-ethernet-services.
   Logical Interface Encapsulation	The Logical Interface Encapsulation field is constrained by your selection in the Physical Interface Encapsulation field. For the physical encapsulation mode of flexible-ethernet-services, your only option is to select vlan-vpls for the logical encapsulation method.
   LDP PW Extension Settings Note: The LDP PW Extension Settings is available only if you have selected the Enable PW Extension check box in the General tab.
   Physical Interface Encapsulation	In the Physical Interface Encapsulation box, select one of the following options: vlan-ccc extended-vlan-ccc flexible-ethernet-services
   Logical Interface Encapsulation	The Logical Interface Encapsulation field is constrained by your selection in the Physical Interface Encapsulation field. For the physical encapsulation mode of vlan-ccc or flexible-ethernet-services, your only option is to select vlan-ccc for the logical encapsulation method. For the physical encapsulation mode of extended-vlan-ccc, your only option is to select extended-vlan-ccc for the logical encapsulation method.
   Traffic Type	Transport all traffic Transports the traffic from all VLANs across the network. When you select this option, the service provisioner is prompted for the VLAN-ID when creating a service order based on this service definition. You need to specify only the Outer Tag protocol ID. Transport single vlan Transports traffic for a specific VLAN across the network. You need to specify both Outer Tag protocol ID and Inner Tag protocol ID. Transport vlan range Limits the traffic across the network to a specific range of VLANs. If you select this option, the service provisioner is prompted for the VLAN-ID range when creating a service order based on this service definition. You need to specify both Outer Tag protocol ID and Inner Tag protocol ID. Transport vlan list Limits the traffic across the network to a specific list of VLANs. If you select this option, the service provisioner is prompted for the VLAN-ID list when creating a service order based on this service definition. You need to specify only the Outer Tag Protocol ID. Note: Make sure to select Editable in Service Order if you want the service provisioner to be able to override this setting.
   VLAN Normalization	Select a value: Normalize to vlan all—To preserve customer VLAN IDs (and customer QoS priorities) across the network. Note: For services that transport a range of VLANs, you must select VLAN Normalization to all. You cannot transport a range of VLANs without normalization. Normalize to vlan none—To preserve no VLAN IDs across the network. Normalize to Dot1q tag—To transport only single-tagged frames across the network core. All port, dot1q , and Q-in-Q traffic is transported across the network Normalize to QinQ tags—To transport only double-tagged frames across the network core. All port, dot1q , and Q-in-Q traffic is transported across the network. Normalization not required—To specify no normalization for port-to-port services Note: Starting with Release 1.0R2, when you newly install Connectivity Services Director, if you select the option to not require normalization in a service definition, the auto-pick option for VLAN IDs and the option to edit the auto-pick behavior in service order are disabled in the service definition. When you create a service order by associating with that service definition, you need to manually enter the VLAN IDs for the interfaces and cannot use the auto-pick functionality. This same behavior also applies to default service templates in which if you select the normalization-not-required functionality, the auto-pick option for VLAN IDs is disabled. For more information about VLAN normalization, see Junos Space Layer 2 Services Overview. For information about VLAN manipulation, see Understanding VLAN Manipulation (Normalization and VLAN Mapping) on Ethernet Services.
   Auto Pick VLAN ID	Indicate how the VLAN ID is determined. By default, this check box is disabled. Clear this check box to allow the service provider to specify the VLAN ID. This option is normally used when no VLAN normalization is applied. Specify the VLAN ID range in VLAN range for manual input. Note: Make sure to select Editable in Service Order if you want the service provisioner to be able to override this setting. Select this check box when VLAN normalization is applied. Specify the VLAN ID pool in VLAN range for auto-pick. Note: Make sure to select Editable in Service Order if you want the service provisioner to be able to override this setting. Note: When the range of VLAN IDs that are automatically assigned by the system (with the auto-pick option enabled during the creation of a service definition) is less than or greater than the range of VLAN IDs that are manually specified (with the manual selection option enabled during the creation of a service definition), the following conditions apply during the creation of a service order with the Editable in Service Order check box selected during service definition creation: If you create a service order with the auto-pick option enabled, the VLAN ID is selected from the auto-pick range, and the value is displayed in the VLAN range for manual input field. If you attempt to change the VLAN ID manually, the value is restricted to the manually configured range. If you create a service order with the auto-pick option disabled, the VLAN ID is selected from the manually configured range, and the value is displayed in the VLAN range for manual input field. If you attempt to change the VLAN ID manually, the value is restricted to the manually configured range.
   VLAN range for auto-pick:	Specify the VLAN ID pool. Range: 1 through 4094
   VLAN range for manual input	Specify the VLAN ID range. Range: 1 through 4094
   Outer Tag Protocol ID	Select the outer tag protocol ID if the Customer traffic type is Transport single VLAN: 0x88a8 0x8100 0x9100 Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPID) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100. To configure the TPIDs manually, use the following commands: set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x9100 set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x88a8 set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x8100
   Inner Tag Protocol ID	Select the inner tag protocol ID: 0x88a8 0x8100 0x9100 Note: You cannot specify the Inner Tag protocol ID if the Customer traffic type is Transport single VLAN.
   Editable in Service Order	To allow the service provisioner to override the outer and inner tag protocol IDs, select the check boxes for those options.
   Default Interface MTU (Bytes)	The default MTU value is 1522 bytes. To allow the service provisioner to override the MTU setting, select the Editable in Service Order check box.
   MTU range for manual-config	In the MTU range fields, type the lowest and highest values for MTU for each UNI. Note: To allow the service provisioner to override the MTU setting, select Editable in Service Order and, in the MTU range fields, type the highest and lowest MTU values.
   PE-CE Interface Rate-Limiting Settings
   Enable Interface Rate Limiting	To enable a service provisioner to limit the available bandwidth, select this check box, and type a default bandwidth limit. Note: Bandwidth settings are available in the service definition when Manage CoS Profiles page is configured with CoS profiles.
   Default bandwidth (Mbps)	Specify the default bandwidth value in Mbps. Default: 10 Mbps Range: 1 Mbps through 100,000 Mbps
   Min Bandwidth (Kbps)	Specify the minimum bandwidth value in Kbps. Default: 1000 Kbps Range: 64 Kbps through 100,000 Kbps
   Max Bandwidth (Mbps)	Specify the maximum bandwidth value in Mbps. For more information on maximum bandwidth see Table 1 Default: 100 Mbps Range: 1 Mbps through 100,000 Mbps
   Increment (Kbps)	Specify a value that defines which values in the range is made available to the service provisioner. Default: 1000 Kbps Range: 64 Kbps through 100,000 Kbps
   Bandwidth – Burst Size Settings
   Burst Size Calculator	Select the preferred option for calculating the burst size: MTU Based If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902. The default value for MTU Factor is 10. Burst Period Based If you select the option Burst Period Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds. The default value for Burst Period is 1. Note: The Burst Size Calculator list is enabled only when you select the Enable Interface Rate Limiting check box.

2. Click Review to view the defined parameters. You can examine and modify the created service order parameters. Alternatively, click the corresponding buttons at the top of the wizard page to navigate to the specific pages pertain to the settings you want to modify. Click Back to return to the previous page of the wizard; else click Cancel to discard the changes.

   After you complete reviewing the settings, click Finish to complete the service definition creation.

To specify the UNI Settings for q-in-q interfaces:

1. Fill in the fields on the Site Settings window.

   Field	Action
   PE-CE Interface Settings- Ethernet Encapsulation
   VLAN Tagging	Select asymmetric tag depth from the list.
   Physical Interface Encapsulation	In the Physical Interface Encapsulation box, select the default physical encapsulation scheme to be used by service orders based on this service definition. For point-to-multipoint services with 802.1Q interfaces, the only option is flexible-ethernet-services.
   Logical Interface Encapsulation	The Logical Interface Encapsulation field is constrained by your selection in the Physical Interface Encapsulation field. For the physical encapsulation mode of flexible-ethernet-services, your only option is to select vlan-vpls for the logical encapsulation method.
   LDP PW Extension Settings Note: The LDP PW Extension Settings is available only if you have selected the Enable PW Extension check box in the General tab.
   Physical Interface Encapsulation	In the Physical Interface Encapsulation box, select one of the following options: vlan-ccc extended-vlan-ccc flexible-ethernet-services
   Logical Interface Encapsulation	The Logical Interface Encapsulation field is constrained by your selection in the Physical Interface Encapsulation field. For the physical encapsulation mode of vlan-ccc or flexible-ethernet-services, your only option is to select vlan-ccc for the logical encapsulation method. For the physical encapsulation mode of extended-vlan-ccc, your only option is to select extended-vlan-ccc for the logical encapsulation method.
   Traffic Type	Transport all traffic Transports the traffic from all VLANs across the network. When you select this option, the service provisioner is prompted for the VLAN-ID when creating a service order based on this service definition. You need to specify only the Outer Tag protocol ID and Inner Tag protocol ID. Transport single vlan Transports traffic for a specific VLAN across the network. You need to specify both Outer Tag protocol ID and Inner Tag protocol ID. Transport vlan range Limits the traffic across the network to a specific range of VLANs. You need to specify both Outer Tag protocol ID and Inner Tag protocol ID. If you select this option, the service provisioner is prompted for the VLAN-ID range when creating a service order based on this service definition. Transport vlan list Limits the traffic across the network to a specific list of VLANs. If you select this option, the service provisioner is prompted for the VLAN-ID list when creating a service order based on this service definition. You need to specify only the Outer Tag Protocol ID. Note: Make sure to select Editable in Service Order if you want the service provisioner to be able to override this setting.
   VLAN Normalization	Select a value: Normalize to vlan all—To preserve customer VLAN IDs (and customer QoS priorities) across the network. Note: For services that transport a range of VLANs, you must select VLAN Normalization to all. You cannot transport a range of VLANs without normalization. Normalize to vlan none—To preserve no VLAN IDs across the network. Normalize to Dot1q tag—To transport only single-tagged frames across the network core. All port, dot1q , and Q-in-Q traffic is transported across the network Normalize to QinQ tags—To transport only double-tagged frames across the network core. All port, dot1q , and Q-in-Q traffic is transported across the network. Normalization not required—To specify no normalization for port-to-port services Note: Starting with Release 1.0R2, when you newly install Connectivity Services Director, if you select the option to not require normalization in a service definition, the auto-pick option for VLAN IDs and the option to edit the auto-pick behavior in service order are disabled in the service definition. When you create a service order by associating with that service definition, you need to manually enter the VLAN IDs for the interfaces and cannot use the auto-pick functionality. This same behavior also applies to default service templates in which if you select the normalization-not-required functionality, the auto-pick option for VLAN IDs is disabled. For more information about VLAN normalization, see Junos Space Layer 2 Services Overview. For information about VLAN manipulation, see Understanding VLAN Manipulation (Normalization and VLAN Mapping) on Ethernet Services.
   Auto Pick VLAN ID	Indicate how the VLAN ID is determined. By default, this check box is disabled. Clear this check box to allow the service provider to specify the VLAN ID. This option is normally used when no VLAN normalization is applied. Specify the VLAN ID range in VLAN range for manual input. Note: Make sure to select Editable in Service Order if you want the service provisioner to be able to override this setting. Select this check box when VLAN normalization is applied. Specify the VLAN ID pool in VLAN range for auto-pick. Note: Make sure to select Editable in Service Order if you want the service provisioner to be able to override this setting. Note: When the range of VLAN IDs that are automatically assigned by the system (with the auto-pick option enabled during the creation of a service definition) is less than or greater than the range of VLAN IDs that are manually specified (with the manual selection option enabled during the creation of a service definition), the following conditions apply during the creation of a service order with the Editable in Service Order check box selected during service definition creation: If you create a service order with the auto-pick option enabled, the VLAN ID is selected from the auto-pick range, and the value is displayed in the VLAN range for manual input field. If you attempt to change the VLAN ID manually, the value is restricted to the manually configured range. If you create a service order with the auto-pick option disabled, the VLAN ID is selected from the manually configured range, and the value is displayed in the VLAN range for manual input field. If you attempt to change the VLAN ID manually, the value is restricted to the manually configured range.
   VLAN range for auto-pick:	Specify the VLAN ID pool. Range: 1 through 4094
   VLAN range for manual input	Specify the VLAN ID range. Range: 1 through 4094
   Outer Tag Protocol ID	Select the outer tag protocol ID if the Customer traffic type is Transport single VLAN: 0x88a8 0x8100 0x9100 Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPID) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100. To configure the TPIDs manually, use the following commands: set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x9100 set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x88a8 set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x8100
   Inner Tag Protocol ID	Select the inner tag protocol ID: 0x88a8 0x8100 0x9100 Note: You cannot specify the Inner Tag protocol ID if the Customer traffic type is Transport all traffic.
   Editable in Service Order	To allow the service provisioner to override the outer and inner tag protocol IDs, select the check boxes for those options.
   MTU range for manual-config	In the MTU range fields, type the lowest and highest values for MTU that the service provisioner can type, for each UNI Note: To allow the service provisioner to override the MTU setting, select Editable in Service Order and, in the MTU range fields, type the highest and lowest MTU values that the service provisioner can type.
   Default Interface MTU (Bytes)	The default MTU value is 1522 bytes. To allow the service provisioner to override the MTU setting, select the Editable in Service Order check box.
   PE-CE Interface Rate-Limiting Settings
   Enable Interface Rate Limiting	To enable a service provisioner to limit the available bandwidth, select this check box, and type a default bandwidth limit. Note: Bandwidth settings are available in the service definition when Manage CoS Profiles page is configured with CoS profiles.
   Default bandwidth (Mbps)	Specify the default bandwidth value in Mbps. Default: 10 Mbps Range: 1 Mbps through 100,000 Mbps
   Min Bandwidth (Kbps)	Specify the minimum bandwidth value in Kbps. Default: 1000 Kbps Range: 64 Kbps through 100,000 Kbps
   Max Bandwidth (Mbps)	Specify the maximum bandwidth value in Mbps. For more information on maximum bandwidth see Table 1 Default: 100 Mbps Range: 1 Mbps through 100,000 Mbps
   Increment (Kbps)	Specify a value that defines which values in the range is made available to the service provisioner. Default: 1000 Kbps Range: 64 Kbps through 100,000 Kbps
   Bandwidth – Burst Size Settings
   Burst Size Calculator	Select the preferred option for calculating the burst size: MTU Based If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902. The default value for MTU Factor is 10. Burst Period Based If you select the option Burst Period Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds. The default value for Burst Period is 1. Note: The Burst Size Calculator list is enabled only when you select the Enable Interface Rate Limiting check box.

2. Click Review to view the defined parameters. You can examine and modify the created service order parameters. Alternatively, click the corresponding buttons at the top of the wizard page to navigate to the specific pages pertain to the settings you want to modify. Click Back to return to the previous page of the wizard; else click Cancel to discard the changes.

   After you complete reviewing the settings, click Finish to complete the service definition creation.

The Review page of the service definition or service order creation and modification wizards enable you to view and evaluate the service parameters and components you configured in preceding steps or pages of the wizard. This page provides a comprehensive, single-page view of all the service elements configured in the different pages of the wizard. You can either click the buttons corresponding to the various settings at the top of the wizard page to directly traverse to the page you want to modify or click the navigation buttons at the bottom of the wizard page to go to the different pages of the wizard.

To examine and modify the configured service definition settings: