show oam ethernet connectivity-fault-management mep-database
Syntax
show oam ethernet connectivity-fault-management mep-database
maintenance-domain domain-name
maintenance-association ma-name
<local-mep local-mep-id>
<remote-mep remote-mep-id>
extensive
Description
On M7i and M10i routers with Enhanced CFEB (CFEB-E), and on M320, M120, MX Series, ACX Series, T320, and T640 routers, display IEEE 802.1ag Operation, Administration, and Management (OAM) connectivity fault management (CFM) database information for CFM maintenance association end points (MEPs) in a CFM session.
In addition, on M120, M320, and MX series routers, also display port status TLV, interface status TLV, and action profile information.
In addition, for Ethernet interfaces on MX Series routers , also display any ITU-T Y.1731 frame delay measurement (ETH-DM) frame counts.
For Ethernet interfaces on MX Series routers, display any ITU-T Y.1731 synthetic frame loss measurement (ETH-SLM) statistics and frame counts.
Options
| maintenance-association ma-name |
Display connectivity fault management information for the specified maintenance association. |
| maintenance-domain domain-name |
Display connectivity fault management information for the specified maintenance domain. |
| local-mep local-mep-id |
(Optional) Display connectivity fault management information for the specified local MEP only. |
| remote-mep remote-mep-id |
(Optional) Display connectivity fault management information for the specified remote MEP only. |
Required Privilege Level
view
Output Fields
Table 1 lists the output fields for the show oam ethernet connectivity-fault-management
mep-database command. Output fields are listed in the approximate
order in which they appear.
Field Name |
Field Description |
|---|---|
Maintenance domain name |
Maintenance domain name. |
Format (Maintenance domain) |
Maintenance domain name format configured. |
Level |
Maintenance domain level configured. |
Maintenance association name |
Maintenance association name. |
Format (Maintenance association) |
Maintenance association name format configured. |
Continuity-check status |
Continuity-check status. |
Interval |
Continuity-check message interval. |
Loss-threshold |
Lost continuity-check message threshold. |
Connection Protection TLV |
Status of the connection protection TLV, if configured on the MEP interface: no, yes If yes, then the transmitted connection protection TLV is decoded and the following three fields are displayed: Prefer me, Protection in use, FRR Flag |
Prefer me |
If set to yes, the path through which CCM was transmitted is preferred (unless the path fails). It is used for signaling a manual-switch command to remote side. Its value can be yes or no. |
Protection in use |
Used for protection decision coordination. Its value is set to yes if the endpoint transmitting the CCM is currently transmitting the user traffic to protection path. Its value can be yes or no. |
FRR Flag |
LSR/LER forwarding the CCM Frame into a bypass tunnel is set. Its value can be yes or no. |
MEP identifier |
Maintenance association end point (MEP) identifier. |
Direction |
MEP direction configured. |
MAC address |
MAC address configured for the MEP. |
Auto-discovery |
Whether automatic discovery is enabled or disabled. |
Priority |
Priority used for CCMs and linktrace messages transmitted by the MEP. |
Interface name |
Interface identifier. |
Interface status |
Local interface status. |
Link status |
Local link status. |
Remote MEP not receiving CCM |
Whether the remote MEP is not receiving CCMs. |
Erroneous CCM received |
Whether erroneous CCMs have been received. |
Cross-connect CCM received |
Whether cross-connect CCMs have been received. |
RDI sent by some MEP |
Whether the remote defect indication (RDI) bit is set in messages that have been received. The absence of the RDI bit in a CCM indicates that the transmitting MEP is receiving CCMs from all configured MEPs. |
CCMs sent |
Number of CCMs transmitted. |
CCMs received out of sequence |
Number of CCMs received out of sequence. |
LBMs sent |
Number of loopback messages (LBMs) sent. |
Valid in-order LBRs received |
Number of loopback response messages (LBRs) received that were valid messages and in sequence. |
1DMs sent |
If the MEP is an initiator for a one-way ETH-DM session: Number of one-way delay measurement (1DM) PDU frames sent to the peer MEP in this session. For all other cases, this field displays 0. |
Valid 1DMs received |
If the MEP is a receiver for a one-way ETH-DM session: Number of valid 1DM frames received. For all other cases, this field displays 0. |
Invalid 1DMs received |
If the MEP is a receiver for a one-way ETH-DM session: Number of invalid 1DM frames received. For all other cases, this field displays 0. |
Out of sync 1DMs received |
If the MEP is a receiver for a one-way ETH-DM session: Number of out-of-sync one-way delay measurement request packets received. |
DMMs sent |
If the MEP is an initiator for a two-way ETH-DM session: Number of Delay Measurement Message (DMM) PDU frames sent to the peer MEP in this session. For all other cases, this field displays 0. |
Valid DMMs received |
If the MEP is an initiator for a two-way ETH-DM session: Number of valid two-way delay measurement packets received. |
Invalid DMMs received |
If the MEP is an initiator for a two-way ETH-DM session: Number of invalid two-way delay measurement packets received. |
DMRs sent |
If the MEP is a responder for a ETH-DM session: Number of Delay Measurement Reply (DMR) frames sent. For all other cases, this field displays 0. |
Valid DMRs received |
If the MEP is an initiator for a two-way ETH-DM session: Number of valid DMRs received. For all other cases, this field displays 0. |
Invalid DMRs received |
If the MEP is an initiator for a two-way ETH-DM session: Number of invalid DMRs received. For all other cases, this field displays 0. |
Valid out-of-order LBRs received |
Number of LBRs received that were valid messages and not in sequence. |
LBRs received with corrupted data |
Number of LBRs received that were corrupted. |
LBRs sent |
Number of LBRs transmitted. |
LTMs sent |
Linktrace messages (LTMs) transmitted. |
LTMs received |
Linktrace messages received. |
LTRs sent |
Linktrace responses (LTRs) transmitted. |
LTRs received |
Linktrace responses received. |
Sequence number of next LTM request |
Sequence number of the next linktrace message request to be transmitted. |
LMM sent |
If the interface is attached to an initiator MEP for a ETH-LM session: Number of loss measurement message (LMM) PDU frames sent to the peer MEP in this session. |
Valid LMM received |
If the interface is attached to an initiator MEP for a ETH-LM session: Number of valid loss measurement request packets received. |
Invalid LMM received |
If the interface is attached to an initiator MEP for a ETH LM session: Number of invalid loss measurement request packets received. |
LMR sent |
If the interface is attached to a responder MEP for a ETH-LM session: Number of loss measurement reply (LMR) frames sent. |
Valid LMR received |
If the interface is attached to an initiator MEP for a ETH LM session: Number of valid LMR frames received. |
Invalid LMR received |
If the interface is attached to an initiator MEP for a ETH-LM session: Number of invalid LMR frames received. |
|
If the interface is attached to an initiator MEP for a ETH-SLM session: Number of synthetic loss measurement (SLM) request packets transmitted from the source MEP to the remote or destination MEP in this session. |
|
If the interface is attached to a responder MEP for a ETH-SLM session: Number of valid SLM PDUs transmitted from the source MEP to the remote or destination MEP. |
|
If the interface is attached to a responder MEP for a ETH-SLM session: Number of invalid SLM PDUs transmitted from the source MEP to the remote or destination MEP. |
|
If the interface is attached to a responder MEP for a ETH-SLM session: Number detail extensive of synthetic loss reply (SLR) frames sent. |
|
If the interface is attached to an initiator MEP for a ETH-SLM session: Number of valid SLR PDUs that the source MEP received from the remote or destination MEP. |
|
If the interface is attached to an initiator MEP for a ETH-SLM session: Number of invalid SLR PDUs that the source MEP received from the remote or destination MEP. |
Remote MEP identifier |
MEP identifier of the remote MEP. |
State (remote MEP) |
State of the remote MEP: idle, start, ok, or failed. |
MAC address |
MAC address of the remote MEP. |
Type |
Whether the remote MEP MAC address was learned using automatic discovery or configured. |
Interface |
Interface of the remote MEP. A seven-digit number is appended if CFM is configured to run on a routing instance of type VPLS. |
Last flapped |
Date, time, and how long ago the remote MEP interface went from down to up. The format is Last flapped: year-month-day hours:minutes:seconds timezone (hours:minutes:seconds ago). For example, Last flapped: 2002-04-26 10:52:40 PDT (04:33:20 ago). |
Remote defect indication |
Whether the remote defect indication (RDI) bit is set in messages that have been received or transmitted. |
Port status TLV |
|
Interface status TLV |
|
Action profile |
Name of the action profile occurrence associated with a remote MEP. |
Last event |
When an action profile occurs, displays the last event that triggered it. |
Last event cleared |
When all the configured and occurred events (under action profile) are cleared, then the action taken gets reverted (such as down interface is made up) and the corresponding time is noted and displayed. |
Action |
Action taken and the corresponding time of the action occurrence. |
Sample Output
- show oam ethernet connectivity-fault- management mep-database
- show oam ethernet connectivity-fault- management mep-database (One-Way ETH-DM)
- show oam ethernet connectivity-fault- management mep-database local-mep remote-mep
- show oam ethernet connectivity-fault- management mep-database remote-mep (Action Profile Event)
- show oam ethernet connectivity-fault- management mep-database (Connection Protection TLV Configured)
- show oam ethernet connectivity-fault- management mep-database
- show oam ethernet connectivity-fault- management mep-database (enhanced continuity measurement)
- show oam ethernet connectivity-fault- management mep-database local-mep remote-mep
show oam ethernet connectivity-fault- management mep-database
user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain vpls-vlan2000 maintenance-association vpls-vlan200
Maintenance domain name: vpls-vlan2000, Format: string, Level: 5
Maintenance association name: vpls-vlan200, Format: string
Continuity-check status: enabled, Interval: 100ms, Loss-threshold: 3 frames
MEP identifier: 200, Direction: up, MAC address: 00:19:e2:b0:74:01
Auto-discovery: enabled, Priority: 0
Interface status TLV: none, Port status TLV: none
Connection Protection TLV: no Interface name: ge-0/0/1.0, Interface status: Active, Link status: Up
Defects:
Remote MEP not receiving CCM : no
Erroneous CCM received : no
Cross-connect CCM received : no
RDI sent by some MEP : no
Statistics:
CCMs sent : 1476
CCMs received out of sequence : 0
LBMs sent : 85
Valid in-order LBRs received : 78
Valid out-of-order LBRs received : 0
LBRs received with corrupted data : 0
LBRs sent : 0
LTMs sent : 1
LTMs received : 0
LTRs sent : 0
LTRs received : 1
Sequence number of next LTM request : 1
1DMs sent : 0
Valid 1DMs received : 0
Invalid 1DMs received : 0
DMMs sent : 0
DMRs sent : 0
Valid DMRs received : 0
Invalid DMRs received : 0
Remote MEP count: 1
Identifier MAC address State Interface
100 00:19:e2:b2:81:4b ok vt-0/1/10.1049088
show oam ethernet connectivity-fault- management mep-database (One-Way ETH-DM)
user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain md6 maintenance-domain ma6
Maintenance domain name: md6, Format: string, Level: 6
Maintenance association name: ma6, Format: string
Continuity-check status: enabled, Interval: 100ms, Loss-threshold: 3 frames
MEP identifier: 101, Direction: down, MAC address: 00:90:69:0a:48:57
Auto-discovery: enabled, Priority: 0
Interface name: ge-0/2/5.0, Interface status: Active, Link status: Up
Defects:
Remote MEP not receiving CCM : no
Erroneous CCM received : no
Cross-connect CCM received : no
RDI sent by some MEP : no
Statistics:
CCMs sent : 1590
CCMs received out of sequence : 0
LBMs sent : 0
Valid in-order LBRs received : 0
Valid out-of-order LBRs received : 0
LBRs received with corrupted data : 0
LBRs sent : 0
LTMs sent : 0
LTMs received : 0
LTRs sent : 0
LTRs received : 0
Sequence number of next LTM request : 0
1DMs sent : 10
Valid 1DMs received : 0
Invalid 1DMs received : 0
DMMs sent : 0
DMRs sent : 0
Valid DMRs received : 0
Invalid DMRs received : 0
Remote MEP count: 1
Identifier MAC address State Interface
201 00:90:69:0a:43:94 ok ge-0/2/5.0
show oam ethernet connectivity-fault- management mep-database local-mep remote-mep
user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain vpls-vlan2000 maintenance-association vpls-vlan200 local-mep 200 remote-mep 100
Maintenance domain name: vpls-vlan2000, Format: string, Level: 5
Maintenance association name: vpls-vlan200, Format: string
Continuity-check status: enabled, Interval: 100ms, Loss-threshold: 3 frames
MEP identifier: 200, Direction: up, MAC address: 00:19:e2:b0:74:01
Auto-discovery: enabled, Priority: 0
Interface name: ge-0/0/1.0, Interface status: Active, Link status: Up
Remote MEP identifier: 100, State: ok
MAC address: 00:19:e2:b2:81:4b, Type: Learned
Interface: vt-0/1/10.1049088
Last flapped: Never
Remote defect indication: false
Port status TLV: none
Interface status TLV: none
show oam ethernet connectivity-fault- management mep-database remote-mep (Action Profile Event)
user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain md5 maintenance-association ma5 remote-mep 200
Maintenance domain name: md5, Format: string, Level: 5
Maintenance association name: ma5, Format: string
Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
MEP identifier: 100, Direction: down, MAC address: 00:05:85:73:e8:ad
Auto-discovery: enabled, Priority: 0
Interface status TLV: none, Port status TLV: none
Interface name: ge-1/0/8.0, Interface status: Active, Link status: Up
Remote MEP identifier: 200, State: ok
MAC address: 00:05:85:73:96:1f, Type: Configured
Interface: ge-1/0/8.0
Last flapped: Never
Remote defect indication: false
Port status TLV: none
Interface status TLV: lower-layer-down
Action profile: juniper
Last event: Interface-status-tlv lower-layer-down
Action: Interface-down, Time: 2009-03-27 14:25:10 PDT (00:00:02 ago)
show oam ethernet connectivity-fault- management mep-database (Connection Protection TLV Configured)
user@host>show oam ethernet connectivity-fault-management mep-database maintenance-domain md5 maintenance-association ma5
If connection-protection is not enabled on down MEPs, but connection-protection TLV is used, MX always sets the protection-in-use flag in connection-protection tlv, while CCMs are sent out. During reversion, this is an indicator to the receiver that protect-path is in use, otherwise the peer (receiver) assumes working is active and reversion does not work as expected. Setting this bit does not affect protection-switching/traffic-loss.
Maintenance domain name: md5, Format: string, Level: 5
Maintenance association name: ma5, Format: string
Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
MEP identifier: 1, Direction: down, MAC address: 00:19:e2:b1:14:30
Auto-discovery: enabled, Priority: 0
Interface status TLV: none, Port status TLV: none
Connection Protection TLV: yes
Prefer me: no, Protection in use: no, FRR Flag: no
Interface name: xe-6/2/0.0, Interface status: Active, Link status: Up
Defects:
Remote MEP not receiving CCM : no
Erroneous CCM received : no
Cross-connect CCM received : no
RDI sent by some MEP : no
Some remote MEP's MAC in error state : no
Statistics:
CCMs sent : 251
CCMs received out of sequence : 0
LBMs sent : 0
Valid in-order LBRs received : 0
Valid out-of-order LBRs received : 0
LBRs received with corrupted data : 0
LBRs sent : 0
LTMs sent : 0
LTMs received : 0
LTRs sent : 0
LTRs received : 0
Sequence number of next LTM request : 0
1DMs sent : 0
Valid 1DMs received : 0
Invalid 1DMs received : 0
Out of sync 1DMs received : 0
DMMs sent : 0
Valid DMMs received : 0
Invalid DMMs received : 0
DMRs sent : 0
Valid DMRs received : 0
Invalid DMRs received : 0
LMMs sent : 0
Valid LMMs received : 0
Invalid LMMs received : 0
LMRs sent : 0
Valid LMRs received : 0
Invalid LMRs received : 0
Remote MEP count: 1
Identifier MAC address State Interface
2 00:90:69:7f:e4:30 show oam ethernet connectivity-fault- management mep-database
user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain md5 maintenance-association ma5
Maintenance association name: ma1, Format: string
Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
MEP identifier: 1, Direction: down, MAC address: 00:14:f6:b6:01:fe
Auto-discovery: enabled, Priority: 0
Interface name: ge-1/0/0.0, Interface status: Active, Link status: Up
Defects:
Remote MEP not receiving CCM : no
Erroneous CCM received : no
Cross-connect CCM received : no
RDI sent by some MEP : no
Statistics:
CCMs sent : 328703
CCMs received out of sequence : 0
LBMs sent : 85
Valid in-order LBRs received : 78
Valid out-of-order LBRs received : 0
LBRs received with corrupted data : 0
LBRs sent : 0
LTMs sent : 0
LTMs received : 0
LTRs sent : 0
LTRs received : 0
Sequence number of next LTM request : 0
1DMs sent : 10
Valid 1DMs received : 10
Invalid 1DMs received : 0
DMMs sent : 20
DMRs sent : 0
Valid DMRs received : 10
Invalid DMRs received : 0
LMM sent : 10
Valid LMM received : 20
Invalid LMM received : 0
LMR sent : 20
Valid LMR received : 10
Invalid LMR received : 0
SLM sent : 10
Valid SLM received : 20
Invalid SLM received : 0
SLR sent : 20
Valid SLR received : 10
Invalid SLR received : 0
Remote MEP count : 1
Identifier MAC address State Interface
2 00:12:1e:fb:ea:7d ok ge-1/0/0.0show oam ethernet connectivity-fault- management mep-database (enhanced continuity measurement)
user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain md5 maintenance-association ma5 local-mep 2001 remote-mep 1001 Maintenance domain name: md5, Format: string, Level: 5 Maintenance association name: ma5, Format: string Continuity-check status: enabled, Interval: 100ms, Loss-threshold: 3 frames MEP identifier: 2001, Direction: down, MAC address: 00:19:e2:b2:81:4a Auto-discovery: enabled, Priority: 0 Interface status TLV: up, Port status TLV: up Interface name: ge-2/0/0.0, Interface status: Active, Link status: Up Remote MEP identifier: 1001, State: ok MAC address : 00:19:e2:b0:74:00, Type: Learned Interface : ge-2/0/0.0 Last flapped : Never + Continuity : 91%, Admin-enable duration: 2100sec, Oper-down duration: 100sec Remote defect indication: false Port status TLV: none Interface status TLV: none
show oam ethernet connectivity-fault- management mep-database local-mep remote-mep
When the timer is not running:
user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain md6 maintenance-association ma6 local-mep 201 remote-mep 101 extensive
Maintenance domain name: md6, Format: string, Level: 6
Maintenance association name: ma6, Format: string
Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
MEP identifier: 201, Direction: up, MAC address: 00:24:dc:48:46:cd
Auto-discovery: enabled, Priority: 0
Interface status TLV: none, Port status TLV: none
Connection Protection TLV: no
Chassis ID: 00:24:dc:48:47:f2
Management Address: 10.216.34.30
Sendid TLV: no
Interface name: ge-5/1/9.0, Interface status: Active, Link status: Up
Remote MEP identifier: 101, State: ok
MAC address: 00:22:83:db:4c:5b, Type: Configured
Interface: ge-5/3/0.0
Last flapped: 2019-02-05 00:45:57 PST (00:54:51 ago)
Continuity: 99%, Admin-enable duration: 3367sec, Oper-down duration: 43sec
Effective loss threshold: 3 frames
Remote defect indication: false
Port status TLV: none
Interface status TLV: none
Remote Management Address: 0.0.0.0
Sendid TLV: no
Sender ID Remote Chassis Subtype: 0
EDM time remaining: N/A
When the timer is running:
user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain md6 maintenance-association ma6 local-mep 201 remote-mep 101 extensive
Maintenance domain name: md6, Format: string, Level: 6
Maintenance association name: ma6, Format: string
Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
MEP identifier: 201, Direction: up, MAC address: 00:24:dc:48:46:cd
Auto-discovery: enabled, Priority: 0
Interface status TLV: none, Port status TLV: none
Connection Protection TLV: no
Chassis ID: 00:24:dc:48:47:f2
Management Address: 10.216.34.30
Sendid TLV: no
Interface name: ge-5/1/9.0, Interface status: Active, Link status: Up
Remote MEP identifier: 101, State: ok
MAC address: 00:22:83:db:4c:5b, Type: Configured
Interface: ge-5/3/0.0
Last flapped: 2019-02-05 00:45:57 PST (00:56:16 ago)
Continuity: 99%, Admin-enable duration: 3451sec, Oper-down duration: 43sec
Effective loss threshold: 3 frames
Remote defect indication: false
Port status TLV: none
Interface status TLV: none
Remote Management Address: 0.0.0.0
Sendid TLV: no
Sender ID Remote Chassis Subtype: 0
EDM time remaining: 894 secs
Release Information
Command introduced in Junos OS Release 8.4.
Support for ITU-T Y.1731 frame delay measurement added in Junos OS Release 9.5.
Support for ITU-T Y.1731 synthetic frame loss measurement added in Junos OS Release 13.2 for MX Series routers.
Support for ITU-T Y.1731 ethernet expected defect function (ETH-ED) added in Junos OS Release 19.1 for MX Series routers
Ethernet expected defect function (ETH-ED) will be supported
on all MX series routers only when enhanced-ip mode is
enabled. ETH-ED will not be supported if CFM is running in centralized
mode.