Rate and give feedback:  Feedback Received. Thank You!

Rate and give feedback: 

X

This document helped resolve my issue

Yes No

Additional Comments

800 characters remaining

May we contact you if necessary?

Name:  

E-mail: 

Enter a valid Email ID

Need product assistance? Contact Juniper Support

Submit

This site is protected by hCaptcha and its Privacy Policy and Terms of Service apply.

English  

English

Example: Tracing RIP Protocol Traffic

Requirements

No special configuration beyond device initialization is required before configuring this example.

Overview

In this example, Device R1 is set to trace routing information updates.

An export policy is also shown because an export policy is required as part of the minimum configuration for RIP.

Figure 1 shows the topology used in this example.

Figure 1: RIP Trace Operations Network Topology

CLI Quick Configuration shows the configuration for all of the devices in Figure 1. The section Step-by-Step Procedure describes the steps on Device R1.

Configuration

CLI Quick Configuration

To quickly configure this example, copy the following commands, paste them into a text file, remove any line breaks, change any details necessary to match your network configuration, and then copy and paste the commands into the CLI at the [edit] hierarchy level.

Step-by-Step Procedure

1. Configure the network interfaces.

   This example shows multiple loopback interface addresses to simulate attached networks.

   [edit interfaces]user@R1# set fe-1/2/0 unit 1 family inet address 10.0.0.1/30
   user@R1# set lo0 unit 1 family inet address 172.16.0.1/32user@R1# set lo0 unit 1 family inet address 192.168.1.1/32
2. Configure the RIP group, and add the interface to the group.

   To configure RIP in Junos OS, you must configure a group that contains the interfaces on which RIP is enabled. You do not need to enable RIP on the loopback interface.

   [edit protocols rip group rip-group]user@R1# set neighbor fe-1/2/0.1
3. Configure RIP tracing operations.
   [edit protocols rip traceoptions]user@R1# set file rip-trace-fileuser@R1# set flag route
4. Create the routing policy to advertise both direct and RIP-learned routes.
   [edit policy-options policy-statement advertise-routes-through-rip term 1]user@R1# set from protocol directuser@R1# set from protocol ripuser@R1# set then accept
5. Apply the routing policy.

   In Junos OS, you can only apply RIP export policies at the group level.

   [edit protocols rip group rip-group]user@R1# set export advertise-routes-through-rip

Results

From configuration mode, confirm your configuration by entering the show interfaces, show protocols, and show policy-options commands. If the output does not display the intended configuration, repeat the configuration instructions in this example to correct it.

If you are done configuring the device, enter commit from configuration mode.

Verification

Confirm that the configuration is working properly.

Checking the Log File

Purpose

Make sure that the RIP route updates are logged in the configured log file.

Action

1. Deactivate the extra loopback interface address on Device R3.
   [edit interfaces lo0 unit 3 family inet]user@R3# deactivate address 172.16.3.3/32user@R3# commit
2. From operational mode on Device R1, enter the show log rip-trace-file command with the | match 172.16.3.3 option.
   user@R1> show log rip-trace-file | match 172.16.3.3

   Mar  1 11:39:53.975192 Setting RIPv2 rtbit on route 172.16.3.3/32, tsi = 0xbb69228
   Mar  1 11:39:59.847118  172.16.3.3/32: metric-in: 16, change: 3 -> 16; # gw: 1, pkt_upd_src 10.0.0.2, inx: 0, rte_upd_src 10.0.0.2
   Mar  1 11:39:59.847568 CHANGE   172.16.3.3/32       nhid 591 gw 10.0.0.2        RIP      pref 100/0 metric 3/0 fe-1/2/0.1 <Delete Int>
   Mar  1 11:39:59.847629 Best route to 172.16.3.3/32 got deleted. Doing route calculation on the stored rte-info

Meaning

The output shows that the route to 172.16.3.3/32 was deleted.