Rate and give feedback:  Feedback Received. Thank You!

Rate and give feedback: 

X

This document helped resolve my issue

Yes No

Additional Comments

800 characters remaining

May we contact you if necessary?

Name:  

E-mail: 

Enter a valid Email ID

Need product assistance? Contact Juniper Support

Submit

This site is protected by hCaptcha and its Privacy Policy and Terms of Service apply.

English  

English

Miscellaneous Commands for a Routing Matrix with a TX Matrix Router

• To display the location of routing matrix components and convert FPCs from T640 router local numbering to routing matrix global numbering, issue the show chassis location fpc command on the TX Matrix router:
  user@router> show chassis location fpc

  Global FPC    LCC     Local FPC
       1          0         1
       2          0         2
       3          0         3
      16          2         0
      17          2         1
      19          2         3
  

• To check the status of the SIB connection between the TX Matrix router and T640 routers, issue the show chassis fabric topology command on the TX Matrix router. All values for each available T640 router (LCC) should be in the UP state. In the following excerpt of output for this command, a routing matrix that contains only LCCs 0 and 2 shows only these two T640 routers as being UP:

  LCC0_SIB-L0_F0,03->SIB-S0_F0,00 UP
  LCC1_SIB-L0_F0,03->SIB-S0_F0,01 RESET
  LCC2_SIB-L0_F0,03->SIB-S0_F0,02 UP
  LCC3_SIB-L0_F0,03->SIB-S0_F0,03 RESET
  

• To verify that the Ethernet links between the TX Matrix router and the T640 router control boards are operational, issue the show chassis ethernet-switch command on the TX Matrix router:
  user@router> show chassis ethernet-switch

  scc-re0:
  --------------------------------------------------------------------------
  Link is good on FE port 4 connected to device: LCC0
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on FE port 6 connected to device: LCC2
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on FE port 8 connected to device: SPMB
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on GE port 13 connected to device: Other RE
    Speed is 1000Mb
    Duplex is full
    Autonegotiate is Enabled
  lcc0-re0:
  --------------------------------------------------------------------------
  Link is good on FE port 1 connected to device: FPC1
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on FE port 2 connected to device: FPC2
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on FE port 3 connected to device: FPC3
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on FE port 8 connected to device: SPMB
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on FE port 10 connected to device: SCC
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on GE port 13 connected to device: Other RE
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  lcc2-re0:
  --------------------------------------------------------------------------
  Link is good on FE port 0 connected to device: FPC0
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on FE port 1 connected to device: FPC1
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on FE port 3 connected to device: FPC3
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on FE port 8 connected to device: SPMB
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on FE port 10 connected to device: SCC
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled
  Link is good on GE port 13 connected to device: Other RE
    Speed is 100Mb
    Duplex is full
    Autonegotiate is Enabled