show services ipsec-vpn ipsec security-associations
Syntax
Release Information
Command introduced before Junos OS Release 7.4.
Description
(Adaptive services interface only) Display IPsec security associations for the specified service set. If no service set is specified, the security associations for all service sets are displayed.
Options
none | — | Display standard information about IPsec security associations for all service sets. |
brief | detail | extensive | — | (Optional) Display the specified level of output. |
service-set service-set-name | — | (Optional) Display information about a particular service set. |
Required Privilege Level
view
List of Sample Output
show services ipsec-vpn ipsec security associations extensiveOutput Fields
Table 1 lists the output fields for the show services ipsec-vpn ipsec security-associations command. Output fields are listed in the approximate order in which they appear.
Table 1: show services ipsec-vpn ipsec security-associations Output Fields
Field Name | Field Description | Level of Output |
|---|---|---|
Service set | Name of the service set for which the IPsec security associations are defined. If appropriate, includes the outside service interface VRF name. | All levels |
Rule | Name of the rule set applied to the security association. | detail extensive |
Term | Name of the IPsec term applied to the security association. | detail extensive |
Tunnel index | Numeric identifier of the specific IPsec tunnel for the security association. | detail extensive |
Local gateway | Gateway address of the local system. | All levels |
Remote gateway | Gateway address of the remote system. | All levels |
IPsec inside interface | Name of the logical interface hosting the IPsec tunnels. | All levels |
Tunnel MTU | MTU of the IPsec tunnel. | All levels |
Local identity | Prefix and port number of the local end. | All levels |
Remote identity | Prefix and port number of the remote end. | All levels |
Primary remote gateway | IP address of the configured primary remote peer. | All levels |
Backup remote gateway | IP address of the configured backup remote peer. | All levels |
State | State of the primary or backup interface: Active, Offline, or Standby. Both ES PICs are initialized to Offline. For primary and backup peers, State can be Active or Standby. If both peers are in a state of Standby, no connection exists yet between the two peers. | All levels |
Failover counter | Number of times a PIC switched between primary and backup interfaces, or the number of times the tunnel switched between the primary and remote peers since the software has been activated. | All levels |
Direction | Direction of the security association: inbound or outbound. | All levels |
SPI | Value of the security parameter index. | All levels |
AUX-SPI | Value of the auxiliary security parameter index.
| All levels |
Mode | Mode of the security association:
| detail extensive |
Type | Type of security association:
| detail extensive |
State | Status of the security association:
| detail extensive |
Protocol | Protocol supported:
| All levels |
Authentication | Type of authentication used: hmac-md5-96, hmac-sha1-96, or none. | detail extensive |
Encryption | Type of encryption algorithm used: aes-cbc (128 bits), aes-cbc (192 bits), aes-cbc (256 bits), des-cbc, 3des-cbc, or None. | detail |
Soft lifetime Hard lifetime | Each lifetime of a security association has two display options, hard and soft, one of which must be present for a dynamic security association. The hard lifetime specifies the lifetime of the SA. The soft lifetime, which is derived from the hard lifetime, informs the IPsec key management system that the SA is about to expire. This information allows the key management system to negotiate a new SA before the hard lifetime expires.
| detail extensive |
Anti-replay service | State of the service that prevents packets from being replayed: Enabled or Disabled. | detail extensive |
Replay window size | Configured size, in packets, of the antireplay service window: 32 or 64. The antireplay window size protects the receiver against replay attacks by rejecting old or duplicate packets. If the replay window size is 0, antireplay service is disabled. | detail |
Sample Output
show services ipsec-vpn ipsec security associations extensive
user@host> show services ipsec-vpn ipsec security-associations
extensive Service set: service-set-1 Rule: _junos_, Term: term-1, Tunnel index: 1 Local gateway: 101.101.101.2, Remote gateway: 14.14.14.4 IPSec inside interface: sp-2/0/0.1 Local identity: ipv4_subnet(any:0,[0..7]=0.0.0.0/0) Remote identity: ipv4_subnet(any:0,[0..7]=0.0.0.0/0) Primary remote gateway: 101.101.101.1, State: Standby Backup remote gateway: 14.14.14.4, State: Active Failover counter: 1 Direction: inbound, SPI: 3743521590, AUX-SPI: 0 Mode: tunnel, Type: dynamic, State: Installed Protocol: ESP, Authentication: hmac-sha1-96, Encryption: 3des-cbc Soft lifetime: Expires in 23043 seconds Hard lifetime: Expires in 23178 seconds Anti-replay service: Enabled, Replay window size: 64 Direction: outbound, SPI: 2551045240, AUX-SPI: 0 Mode: tunnel, Type: dynamic, State: Installed Protocol: ESP, Authentication: hmac-sha1-96, Encryption: 3des-cbc Soft lifetime: Expires in 23043 seconds Hard lifetime: Expires in 23178 seconds Anti-replay service: Enabled, Replay window size: 64
