Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

TechLibrary
Navigation

Configuring VLANs for EX Series Switches (J-Web Procedure)

You can use the VLAN Configuration page to add a new VLAN or to edit or delete an existing VLAN on an EX Series switch.

To access the VLAN Configuration page:

  1. Select Configure > Switching > VLAN.

    The VLAN Configuration page displays a list of existing VLANs. If you select a specific VLAN, the specific VLAN details are displayed in the Details section.

    Note: After you make changes to the configuration on this page, you must commit the changes immediately for them to take effect. To commit all changes to the active configuration, select Commit Options > Commit. See Using the Commit Options to Commit Configuration Changes for details about all commit options.

  2. Click one of the following options:
    • Add—Creates a VLAN.
    • Edit—Edits an existing VLAN configuration.
    • Delete—Deletes an existing VLAN.

      Note: If you delete a VLAN, the VLAN configuration for all the associated interfaces is also deleted.

    When you are adding or editing a VLAN, enter information as described in Table 1.

Table 1: VLAN Configuration Details

Field

Function

Your Action

General tab

VLAN Name

Specifies a unique name for the VLAN.

Enter a name.

VLAN ID/Range/VLAN ID/List

Note: EX4300 switches support only VLAN ID/List and not VLAN Range.

Specifies the identifier or range for the VLAN.

Select one of the following options:

  • VLAN ID—Type a unique identification number from 1 through 4094. If no value is specified, the ID defaults to 0.
  • VLAN Range/List—Type a number range to create VLANs with IDs corresponding to the numbers in the range. For example, the range 2–3 creates two VLANs with the IDs 2 and 3.

Description

Describes the VLAN.

Enter a brief description for the VLAN.

MAC-Table-Aging-Time

Note: This option is not supported on EX4300 switches.

Specifies the maximum time that an entry can remain in the forwarding table before it ages out.

Type the number of seconds from 60 through 1000000.

Input filter

Specifies the VLAN firewall filter that is applied to incoming packets.

To apply an input firewall filter, select the firewall filter from the list.

Output filter

Specifies the VLAN firewall filter that is applied to outgoing packets.

To apply an output firewall filter, select the firewall filter from the list.

Ports tab

Ports

Note: This option is not supported on EX4300 switches.

Specifies the ports (interfaces) to be associated with this VLAN for data traffic. You can also remove the port association.

Click one of the following options:

  • Add—Select the ports from the available list. For an EX8200 Virtual Chassis configuration, select the member, FPC, and the interface from the list.
  • Remove—Select the port that you do not want associated with the VLAN.

IP address tab

IPv4 address

Specifies IPv4 address options for the VLAN.

Select IPv4 address to enable the IPv4 address options.

To configure IPv4:

  1. Enter the IP address.
  2. Enter the subnet mask—for example, 255.255.255.0. You can also specify the address prefix.
  3. To apply an input firewall filter to an interface, select the firewall filter from the list.
  4. To apply an output firewall filter to an interface, select the firewall filter from the list.
  5. Click the ARP/MAC Details button. Enter the static IP address and MAC address in the window that is displayed.

Note: In EX4300 switches, you also need to select L2 Interface in the window that is displayed.

IPv6 address

Specifies IPv6 address options for the VLAN.

Select IPv6 address to enable the IPv6 address options.

To configure IPv6:

  1. Enter the IP address—for example: 2001:ab8:85a3::8a2e:370:7334.
  2. Specify the subnet mask.

Voip tab

Ports

Specifies the ports to be associated with this VLAN for voice traffic. You can also remove the port association.

Click one of the following options:

  • Add—Select the ports from the list of available ports. For an EX8200 Virtual Chassis configuration, select the member, FPC, and the interface from the list.
  • Remove—Select the port that you do not want associated with the VLAN.
 

Related Documentation

 

Published: 2014-04-23

Previous Page Next Page