EX4100-F Site Guidelines and Requirements

You must install the switch in a rack or cabinet. You must house it in a dry, clean, well-ventilated, and temperature-controlled environment.

Follow these environmental guidelines:

• Ensure that the site is as dust-free as possible. Dust can clog air intake vents and filters, reducing the efficiency of the switch cooling system.

• Maintain ambient airflow for normal switch operation. If the airflow is blocked or restricted, or if the intake air is too warm, the switch might overheat. If the switch overheats, the switch temperature monitor may shut down the device to protect the hardware components.

The following are the required environmental conditions for normal switch operation of EX4100-F switches.

• Switch: All EX4100-F switch models

• Altitude: No performance degradation up to 5,000 feet (1, 524 meters)

• Relative humidity: Normal operation ensured in relative humidity range of 10% through 85%, noncondensing

• Temperature:

  • Normal operation ensured in temperature range of 32 °F through 113 °F (0 °C through 45 °C)

  • Nonoperating storage temperature in shipping container: –40 °F through 158 °F (–40 °C through 70 °C)

• Seismic tolerance: Tested for Zone 4 earthquake safety.

Note:

With 10G-Base-T pluggable, max temperature is reduced to 40C up to 5,000ft elevation.

Note:

Install the EX4100-F switch only in restricted areas, such as dedicated equipment rooms and equipment closets. Install the switch in accordance with Articles of the National Electrical Code, ANSI/NFPA 70.

Note:

For EX4100-F-12P, max operating temperature is limited to 40C, 5000 feet for Under the Desk mounting. For desk mounting and two-post rack mounting configurations, max operating temperature is limited to 44C, 5000 feet.

For rack mounting of EX4100-F-12P and EX4100-F-12T, 3RU clearance is required above the units.

Industrial grade SFP+ optics (10GE) is required for EX4100-F-12P and EX4100-F-12T above 40C operating ambient temperature.

Efficient device operation requires proper site planning and maintenance. It also requires proper layout of the equipment, rack or cabinet, and wiring closet.

To plan and create an acceptable operating environment for your device and prevent environmentally caused equipment failures:

• Keep the area around the chassis free from dust and conductive material, such as metal flakes.

• Follow the prescribed airflow guidelines to ensure that the cooling system functions properly. Ensure that exhaust from other equipment does not blow into the intake vents of the device.

• Follow the prescribed electrostatic discharge (ESD) prevention procedures to prevent damaging the equipment. Static discharge can cause components to fail completely or intermittently over time.

• Install the device in a secure area, so that only authorized personnel can access the device.

Table 1 describes the factors you must consider while planning the electrical wiring at your site.

Warning:

You must provide a properly grounded and shielded environment and use electrical surge-suppression devices.

Avertissement Vous devez établir un environnement protégé et convenablement mis à la terre et utiliser des dispositifs de parasurtension.

Table 1: Site Electrical Wiring Guidelines

Site Wiring Factor	Guidelines
Signaling limitations	If your site experiences any of the following problems, consult experts in electrical surge suppression and shielding: Improperly installed wires cause radio frequency interference (RFI). Damage from lightning strikes occurs when wires exceed recommended distances or pass between buildings. Electromagnetic pulses (EMPs) caused by lightning damage unshielded conductors and electronic devices.
Radio frequency interference	To reduce or eliminate RFI from your site wiring, do the following: Use a twisted-pair cable with a good distribution of grounding conductors. If you must exceed the recommended distances, use a high-quality twisted-pair cable with one ground conductor for each data signal, when applicable.
Electromagnetic compatibility	If your site is susceptible to problems with electromagnetic compatibility (EMC), particularly from lightning or radio transmitters, seek expert advice. Strong sources of electromagnetic interference (EMI) can cause: Destruction of the signal drivers and receivers in the device Electrical hazards as a result of power surges conducted over the lines into the equipment.

You can mount the device on two-post racks or four-post racks.

Rack requirements consist of:

• Rack type.

• Mounting bracket hole spacing.

• Rack size and strength.

• Rack connection to the building structure.

Table 2 provides the rack requirements and specifications.

Table 2: Rack Requirements and Specifications

Rack Requirement	Guidelines
Rack type	A U is the standard rack unit defined by the Electronic Components Industry Association (http://www.ecianow.org). You can mount the device on a rack that provides bracket holes or hole patterns spaced at 1U (1.75 in. or 4.45 cm) increments and meets the size and strength requirements to support the weight.
Mounting bracket hole spacing	The holes in the mounting brackets are spaced at 1U (1.75 in. or 4.45 cm) so that the device can be mounted in any rack that provides holes spaced at that distance.
Rack size and strength	Ensure that the: Rack complies with the size and strength standards of a 19-in. rack as defined by the Electronic Components Industry Association (http://www.ecianow.org). Rack rails are spaced widely enough to accommodate the external dimensions of the device chassis. Ensure also that the outer edges of the front mounting brackets extend the width of the chassis to 19 in. (48.2 cm). Rack is strong enough to support the weight of the device. Spacing of rails and adjacent racks provides for proper clearance around the device and rack.
Rack connection to building structure	Secure the rack as follows: Secure the rack to the building structure. If your geographical area is earthquake-prone, secure the rack to the floor. Secure the rack to the ceiling brackets as well as wall or floor brackets for maximum stability.

You can mount the device in a cabinet that contains a 19-in. rack.

Cabinet requirements consist of:

• Cabinet size.

• Clearance requirements.

• Cabinet airflow requirements.

Table 3: Cabinet Requirements and Specifications

Cabinet Requirement	Guidelines
Cabinet size	For EX4100-F-12P and EX4100-F-12T, the minimum cabinet size is 27 in. (68.5 cm) deep. Large cabinets improve airflow and reduce chances of overheating
Cabinet clearance	For EX4100-F-12P and EX4100-F-12T switches 22 inch (55.88 cm) internal free space is required within the cabinet.
Cabinet airflow requirements	When you mount the device in a cabinet, ensure that ventilation through the cabinet is sufficient to prevent overheating, as follows: Ensure adequate cool air supply to dissipate the thermal output of the device or devices. Ensure that the hot air exhaust of the chassis exits the cabinet without recirculating into the device. An open cabinet (without a top or doors) that employs hot air exhaust extraction from the top ensures the best airflow through the chassis. If the cabinet contains a top or doors, perforations in these elements assist with removing the hot air exhaust. Install the device in the cabinet in a way that maximizes the open space on the side of the chassis that has the hot air exhaust. Route and secure all cables to minimize the blockage of airflow to and from the chassis. Ensure that the spacing of rails and adjacent cabinets is such that proper clearance exists around the device and cabinet. A cabinet larger than the minimum required provides better airflow and reduces the chance of overheating.

When planning the site for installing an EX4100-F switch, you must allow sufficient clearance around the installed switch.

See:

• Figure 1 for clearance requirements for airflow and hardware maintenance for EX4100-F-12P and EX4100-F-12T switches.

• Figure 2 for clearance requirements for airflow and hardware maintenance for the EX4100-F-24T switch.

• Figure 3 for clearance Requirements for airflow and hardware maintenance for the EX4100-F-24P switch.

• Figure 4 for clearance requirements for airflow and hardware maintenance for the EX4100-F-48P switch.

• Figure 5 for clearance requirements for airflow and hardware maintenance for the EX4100-F-48T switch.

• For the cooling system to function properly, the airflow around the chassis must be unrestricted.

• If you are mounting the switch in a rack or cabinet with other equipment, or if you are placing it on the desktop or floor near other equipment, ensure that the exhaust from other equipment does not blow into the intake vents of the chassis.

• Leave at least 24 in. (61 cm) in front of the switch and behind the switch. For service personnel to remove and install hardware components, you must leave adequate space at the front and back of the switch. It is recommended that you allow at least 30 in. (76.2 cm) in front of the rack or cabinet and 24 in. (61 cm) behind the rack or cabinet.