Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 
 

Protocols and Applications Supported by the MX2K-MPC11E

Table 1 contains protocols and applications supported by the MX2K-MPC11E line cards on the MX2010 and MX2020 routers.

Note:

The MX2K-MPC11E line card is supported in Junos OS 19.3R2 and later 19.3 releases and in Junos OS 20.1R1 and later Junos OS releases. It is not supported in Junos OS 19.4.

A dash indicates that the protocol or application is not supported.

Table 1: Protocols and Applications Supported by MPC11E line cards in the MX2010 and MX2020 Routers

Protocol or Application

First Supported Junos OS Release for MX2K-MPC11E

Access Node Control Protocol (ANCP)

-

Accepts traffic destined for generic routing encapsulation (GRE) tunnels

Release

  • -

  • 19.3R2

Accepts traffic destined for Distance Vector Multicast Routing Protocol (DVMRP) (IP-in-IP) tunnels

-

Bidirectional Forwarding Detection protocol (BFD)

Centralized BFD

19.3R2

Distributed BFD

19.3R2

Inline BFD (single-hop only)

19.3R2

Single-hop BFD

19.3R2

Multihop BFD

19.3R2

Micro BFD

19.3R2

BFD over Integrated routing and bridging (IRB) interfaces

19.3R2

BFD over Pseudowire over LT and RLT interfaces

19.3R2

Virtual circuit connectivity verification (VCCV) BFD for Layer2 VPNs and Layer2 circuits

19.3R2

VCCV BFD for VPLS

-

BFD authentication

-

Seamless BFD

-

Internet Control Message Protocol (ICMP) and ICMPv6

19.3R2

Border Gateway Protocol (BGP)

19.3R2

Bridge protocol data units (BPDUs)

-

BGP/MPLS virtual private networks (VPNs)

19.3R2

Routing Instance:

  • Logical system

  • Virtual routing and forwarding (VRF)

19.3R2

Load Balancing

19.3R2

Class of service (CoS) First Supported Junos OS Release for MX2K-MPC11E

Maintain CoS across internal tunnel interfaces

19.3R2

Packet Rewrites on DSCP, Inet Precedence (both Ipv4 and IPv6) and EXP bits

19.3R2

Behavior aggregate (BA) classification

19.3R2

BA classification based on 802.1p of payload for core-facing VPLS interfaces

19.3R2

BA DSCP classification of MPLS packets for L3VPN and MPLS interfaces

19.3R2

BA DSCP classification of MPLS packets for VPLS LSI interfaces

19.3R2

Rate limit option for per-port queues

19.3R2

BA DSCP classification for VPLS/CCC family

19.3R2

Configurable shaping overhead for scheduling

19.3R2

Class of service (CoS) per port:

  • Eight queues per port

  • Excess-rate and excess-priority configurations at the queue level

  • Shaping at the port level

  • Shaping at the queue level

  • Scheduling of queues based on the weighted round-robin (WRR) per excess-priority class

  • Round-robin scheduling of the queues per priority class

  • Weighted random early detection (WRED)

19.3R2

Class of service (CoS) per virtual LAN (VLAN):

  • Accounting, filtering, and policing

  • IEEE 802.1p rewrite

  • IEEE 802.1p classification

19.3R2

Class of service (CoS) per Point-to-Point Protocol over Ethernet (PPPoE) or Dynamic Host Configuration Protocol (DHCP) subscriber interfaces:

  • Accounting, filtering, and policing

  • IEEE 802.1p rewrite

  • Classification

  • Excess-rate and excess-priority configuration at the queue level

  • Shaping at the queue level

  • Scheduling of queues based on weighted round-robin (WRR) per priority class

  • Weighted random early detection (WRED)

Release

  • -

  • -

  • -

  • -

  • -

  • -

  • -

Ingress and egress hierarchical class-of-service (CoS) shaping and hierarchical-scheduler:

Note:

Only egress is supported.

  • Group of virtual LANs (VLANs) level

  • VLAN level

  • Port level

19.3R2

Queue depth monitoring

19.3R2

Layer 2 Features First Supported Junos OS Release for MX2K-MPC11E

Trunk ports

19.3R2

Layer 2 support for MX Series Virtual Chassis

19.3R2

Layer 2 and Layer 2.5, IRB and Spanning Tree Protocols (xSTP)

19.3R2

IEEE 802.1ad provider bridges

19.3R2

L2TPv2 silent failover and peer interface

19.3R2

Multichassis LAG—active/active and active/standby

-

Multichassis LAG—active/active with IGMP snooping

-

Link aggregation group (LAG)—VLAN-CCC encapsulation

19.3R2

IGMP snooping with bridging, IRB, and VPLS

-

Layer 2 VPN interfaces support VLAN ID list

19.3R2

Link aggregation (IEEE 802.3ad)

19.3R2

Link Aggregation Control Protocol (LACP)

19.3R2

Link Layer Discovery Protocol (LLDP)

19.3R2

Local loopback

19.3R2

MAC learning and policing

19.3R2

MAC filtering

19.3R2

Layer 2 Services supported with pseudowire headend termination (PWHT) First Supported Junos OS Release for MX2K-MPC11E

Layer 2 circuit terminates into the following Layer 2 services over the logical tunnel (lt) and redundant logical tunnel (rlt)

  • Bridge domain

  • EVPN Single home

  • VPLS

20.1R1

VLAN cross-connect on transport interface

20.1R1

Psuedowire service Layer 2 interface

  • MAC clear, MAC limit, MAC move, MAC pinning, and Static MAC

  • Statistics

20.1R1

Psuedowire service interfaces

  • MAC Learning, MAC Table Aging, and forwarding on aggregated Ethernet interfaces

  • Simple dual tag bridging (with VLAN map operations)

  • BUM traffic handling including split horizon

  • Native outer VLAN, VLAN tags in routing instances

  • Outer list, Inner list, and Outer VLAN-id list

  • Static MAC and Stacked VLAN

  • input-vlan-maps and output-vlan-maps

  • implicit-vlan-rewrites

  • no-local-switching, local-switching, and policer/ filter

  • mac-table-size, mac-aging-time, and no-mac-learning

  • interface-mac-limit and interface-mac-pinning

  • tag-protocol-id for Layer 2 services over logical tunnel interface (lt)

20.1R1

Firewall filters and policers First Supported Junos OS Release for MX2K-MPC11E

Family Inet/Inet6/MPLS

19.3R2

All the static match conditions/actions

19.3R2

Dynamic actions (port-mirroring, next hop, routing instance)

19.3R2

Interface-specific filters

19.3R2

BGP Flow specification

19.3R2

Two color and three color policers (SRTCM and TRTCM)

19.3R2

FTF (filter attachment on routing table)

19.3R2

Firewall attachment on Aggregated Ethernet Interfaces (AE)

19.3R2

Hierarchical Policers

19.3R2

Family Any/CCC (for firewall)

19.3R2

Percentage Bandwidth policers

-

Shared Bandwidth policers

-

Logical Interface policers

19.3R2

Physical interface policers

-

Firewall Based GRE ENCAP/DECAP

19.3R2

Fast lookup filter

19.3R2

Jvision (firewall filter counters only)

19.3R2

Filter-based tunneling:

  • GRE-in-UDP encapsulation and decapsulation

  • MPLS-over-UDP decapsulation

19.3R2

Filter-based forwarding:

  • Next-IP

  • Next-interface

19.3R2

Interface-group

19.3R2

Family bridge filter

19.3R2

VPLS family filter

19.3R2

Filter attachment on IRB, PSoLT, PSoRLT and bridge-domain

19.3R2

Other Features First Supported Junos OS Release for MX2K-MPC11E

Distributed Denial-of-Service (DDoS) Protection

19.3R2

DVMRP and GRE support—access side and server side

-

Managing Power

19.3R2

Ethernet Ring Protection Switching with multiple G.8032 instances

-

Flexible Queuing Mode

-

IEEE 802.1ag Ethernet OAM Continuity Check protocol

-

IEEE 802.1ag Ethernet OAM Linktrace protocol

-

IEEE 802.1ag Ethernet OAM Loopback protocol

-

IEEE 802.1ag:

  • Maintenance association intermediate point (MIP)

  • Continuity check message (CCM)

  • Stacked VLAN tagging

  • Trunk ports

  • VPLS

  • VPWS

  • VLAN circuit cross-connect (CCC) encapsulation and

  • Translational cross-connect (TCC) encapsulation

Release

  • -

  • -

  • 19.3R2

  • -

  • -

  • 19.3R2

  • 19.3R2

  • -

IEEE 802.1ag optional type, length, and value (TLVs) support Configuring Port Status TLV and Interface Status TLV

19.3R2

IEEE 802.3ah distributed periodic packet management (PPM) process, alarm indication signal (AIS), and remote defect indication (RDI)

19.3R2

Flexible Ethernet encapsulation

19.3R2

Graceful Routing Engine Switchover (GRES)

19.3R2

IGMPv3 support with snooping disabled

19.3R2

Intelligent Oversubscription on MIC and MPC Interfaces Overview

19.3R2

Integrated routing and bridging (IRB)

-

Unified In-service software upgrade (Unified ISSU) with Enhanced Mode

21.2R1

Unified ISSU with enhanced mode (On MPC11E with sub line cards (SLCs)

21.4R1

Interoperability with MPCs

19.3R2

Interoperability with MS-DPCs/MS-MPCs

-

Interoperability with MX Series Flexible PIC Concentrators (MX-FPC)

-

IPv4

19.3R2

IPv4 multicast

  • PIM sparse mode (PIM-SM)

  • PIM source-specific multicast (PIM-SSM)

  • Point to multipoint (P2MP)

  • Multicast-only fast reroute (MoFRR)

  • Draft-rosen MVPN

Release

  • 19.3R2

  • 19.3R2

  • 19.3R2

  • 19.3R2

  • 19.3R2

IPv6

19.3R2

IPv6 MLD

19.3R2

IPv6 multicast

  • PIM sparse mode (PIM-SM)

  • PIM source-specific multicast (PIM-SSM)

  • Point to multipoint (P2MP)

  • Multicast-only fast reroute (MoFRR)

  • Draft-rosen MVPN

Release

  • 19.3R2

  • 19.3R2

  • 19.3R2

  • 19.3R2

  • 19.3R2

IPv6 Neighbor Discovery

19.3R2

IS-IS

19.3R2

ITU-T Y.1731 timestamping support on MX Series routers

-

Optimizing Fabric Path for Abstracted Fabric Interface

20.1R1

MPLS Features supported in Junos OS Release for MX2K-MPC11E

Switching of pseudowire segments (multisegment pseudowires with BGP-L2VPN)

19.3R2

LDP signaling for VPLS (LDP-VPLS) and MAC flush message processing (MAC-FLUSH-TLV)

-

RSVP graceful restart interoperability with Cisco using Nodal Hello

-

Failure action on BFD session down of RSVP LSPs

19.3R2

OSPF and IS-IS loop-free alternates (LFA)

19.3R2

4/5 label MPLS operation

19.3R2

Virtual circuit connectivity verification (VCCV) BFD

19.3R2

Point to multipoint using the enhanced-ip command (support for NG-MVPN and P2MP load balancing over aggregated Ethernet)

-

MPLS-FRR bypass link protection

19.3R2

Load sharing across 64 ECMP next hops

19.3R2

MPLS-FRR VPLS instance prioritization

-

Five label stack on ingress

19.3R2

MPLS node protection, link protection, and statistics for static LSPs

19.3R2

End-to-end LSP MPLS ping

20.2R1

LDP pseudowire auto-sensing

20.2R1

LSP ping for circuit cross-connect (CCC) and CCC secondary standby LSP

20.2R1

Edge node failure protection of LDP-signaled pseudowire

20.2R1

Link and node protection for static LSPs

20.2R1

Support of statistics for static LSPs

20.2R1

Stitching of pseudowire segments (multisegment pseudowires with BGP Layer 2 VPN)

20.2R1

Cross-connect logical interface to two unsignaled virtual circuits terminating on different egress Provider Edge (PE) devices

20.2R1

Generic Associated Channel Label (GAL) and Generic Associated Channel Header (G-Ach) and application to BFD or LSP ping

20.2R1

Ultimate hop popping (UHP) support for LSPs

20.2R1

GMPLS co-routed packet LSPs

20.2R1

LDP downstream-on-demand

20.2R1

Seamless Multicast MPLS: intSegmented P2P and P2MP LSPs with MVPN interworking

20.2R1

PS Interface support for PW Redundancy Condition

20.2R1

mvrp

-

Multitopology routing

-

Nonstop active routing (NSR)

19.3R2

OSPF

19.3R2

Packet mirroring

19.3R2

IEEE 802.1ah provider backbone bridging (PBB)

-

Push a tag on Ethernet VPLS and Ethernet CCC tag encapsulations

-

RSVP Overview

19.3R2

RIP

19.3R2

SNMP

19.3R2

Spanning Tree Protocols:

  • IEEE 802.1s Multiple Spanning Tree Protocol (MSTP) (part of IEEE 802.1Q VLANs)

  • IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)

  • IEEE 802.1D Spanning Tree Protocol (STP)

  • Per-VLAN Spanning Tree (PVST)

  • Bridge protocol data units (BPDUs) guard and loop guard

  • STP inter-protocol action profiles and MAC flush (in VPLS multi-homing, flush all MACs when there is a change in the STP interface state due to root protect)

-

Subscriber Management and Services:

  • Enhanced subscriber management—Uplink communications to the core network only

19.3R2

Synchronous Ethernet

20.1R1

Two-Way Active Measurement Protocol (TWAMP)

19.3R2

Tunnel services

  • Clear DF-Bit (Don't Fragment Bit)

19.3R2

Unified in-service software upgrade (ISSU)

-

Unnumbered Ethernet Interface

-

VLANs IEEE 802.1Q:

  • VLAN stacking and rewriting

  • Flexible VLAN tagging

  • Single VLAN tags

  • Dual VLAN tags

  • IP service for nonstandard TPID and stacked VLAN tags

19.3R2

Virtual Chassis: MPLS IPv4 and IPv6, unicast, multicast forwarding, VPLS, NSR for Layer 3/MPLS services

-

Virtual private LAN service (VPLS):

  • BGP multihoming for inter-AS VPLS

  • Gigabit Ethernet as core-facing interface

  • Configurable label block sizes

  • Hashing L3/L4 fields under Ethernet pseudowire for VPLS encapsulation, CCC encapsulation, and MPLS encapsulation

  • VPLS flood forwarding table filter (FTF), input FTF

  • Broadcast, unicast unknown, and multicast (BUM) traffic hashing over LAG

-

Virtual private network (VPN)

19.3R2

Virtual Router Redundancy Protocol (VRRP) for IPv4

19.3R2

VPLS packet flooding to the right set of interfaces across mesh groups

-

WAN-PHY mode

19.3R2

Flow monitoring and services First Supported Junos OS Release for MX2K-MPC11E

Inline IP Flow Information Export (IPFIX)

19.3R2

Inline flow monitoring for MPLS, MPLS-IPv4 and MPLS-IPv6 traffic (IPFIX and V9 formats)

19.3R2

Inline flow monitoring for IPv4 or IPv6 traffic on next-hop based GRE Tunnels and ps interfaces

19.3R2

Port mirroring family bridge CCC encapsulation

19.3R2

Port mirroring with analyzer instance [edit forwarding-options analyzer]

-

Packet slice for port mirroring

-

Labeled-switched-paths (LSPs) including accounting, policers, and filtering

19.3R2

Minimum LDP Configuration

19.3R2

MACSec First Supported Junos OS Release for MX2K-MPC11E

GCM-AES-128 MACSec Encryption, 802.1AE-2006

19.3R2

GCM-AES-256 MACSec Encryption, 802.1AEbn-2011

19.3R2

Mobile IP

-

Multichassis link aggregation

-

Multiple Tag Protocol Identifiers (TPIDs)

19.3R2