Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 
ON THIS PAGE
 

QFX10000 AC Power System

QFX10000-PWR-AC Power Supply

QFX10000-PWR-AC Power Supply Description

The QFX10000-PWR-AC power supply is a 2700 W, hot-insertable, hot-removable, field-replaceable unit (FRU). You can install up to six power supplies in a QFX10008 in the slots labeled PSU 0 through PSU 5 (top to bottom) located in the rear of the chassis. In QFX10016, you can install up to 10 power supplies in the slots labeled PSU 0 through PSU 9. Power supplies install in any available power supply slot.

The AC power supply supports 200–240 VAC. Each AC power supply has two independent 16 A rated AC inlets on the faceplate. The output is 12 VDC; the output power is 2700 W.

Warning:

The switch is pluggable type A equipment installed in a restricted-access location. It has a separate protective earthing terminal on the chassis that must be connected to earth ground permanently to ground the chassis adequately and protect the operator from electrical hazards.

CAUTION:

Before you begin installing the switch, ensure that a licensed electrician has attached an appropriate grounding lug to the grounding cable that you supply. Using a grounding cable with an incorrectly attached lug can damage the switch.

Note:

All base configuration QFX10008 switches are shipped with three power supplies; base configuration for QFX10016 switches are shipped with five power supplies. Covers are installed over the remaining power supply slots. You can add additional power supplies to base configuration switches as necessary. To calculate the number of additional power supplies needed for your specific system, see Calculating Power Requirements for a QFX10008 and Calculating Power Requirements for a QFX10016. For details about different switch configurations, see QFX10008 Configurations and Upgrade Options and QFX10016 Components and Configurations.

The JNP10K-PWR-AC power supplies do not share power.

Each QFX10000-PWR-AC power supply weighs approximately 6.8 lb (3.08 kg) and has 2 independent 16 A rated AC inlets on the faceplate. Although each inlet provides sufficient input power to provide full output, always connect to a dedicated AC power feed to provide redundancy. Only one power feed is operational at a time.

QFX10000 modular switches employ automatic transfer switch (ATS) technology. The system provides 2n source redundancy and n+1 power supply redundancy, allowing you to use fewer power supplies than you would require in a 2n configuration. Should one power source fail, ATS switches the power supply to the alternate source.

Note:

For redundancy, always plug the two power cords from each power supply:

  • INP1 into a UPS

  • INP2 into the public electricity supply

Each QFX10000-PWR-AC power supply has a power switch with international markings for on (|) and off (O), a fan, and four LEDs on the faceplate that indicate the status of the power supply. See Figure 1.

Figure 1: QFX10000-PWR-AC Power SupplyQFX10000-PWR-AC Power Supply

Each QFX10000-PWR-AC power supply comes with two power cord retainers that hold the power cords in place. See Figure 2. Each power cord retainer has a clip and an adjustment nut. The ends of the clip hook into the bracket holes on each side of the AC appliance inlet on the faceplate. The adjustment nut holds the power cord in the correct position. For instructions for installing the power cord retainers, see Connect AC Power to a QFX Modular Chassis.

Figure 2: Power Cord Retainer for a QFX10000-PWR-AC Power SupplyPower Cord Retainer for a QFX10000-PWR-AC Power Supply

Each power supply connects to the power rail in the switch. The power rail distributes the output power produced by the power supplies to different switch components. Each AC power supply provides power to all the components in the switch.

Each power supply has its own fan and is cooled by its own internal cooling system. Hot air exhausts from the rear of the chassis.

QFX10000-PWR-AC Power Specifications

Table 1 lists the power specifications for the AC power supply used in a QFX10000 modular chassis.

Table 1: Power Specifications for a QFX10000-PWR-AC Power Supply

Item

Specifications

AC input voltage

Operating range: 200–240 VAC

AC input line frequency

50–60 Hz

AC input current rating

16 A

AC output power

2700 W

Table 2 shows the physical specifications for a QFX10000-PWR-AC power supply.

Table 2: Physical Specifications for a QFX10000-PWR-AC Power Supply

Specification

Value

Height

3.5 in. (8.89 cm)

Width

3.6 in. (9.14 cm)

Depth

14.4 in. (6.53 cm)

Weight

6.8 lb (3.08 kg)

JNP10K-PWR-AC2 Power Supply

The JNP10K-PWR-AC2 power supply is a high-capacity, high-line model that is designed to support either AC or DC systems in either a low-power or high-power mode. The power supply takes AC input and provides DC output of 12.3 VDC, 5000 W with a single feed and 5500 W with a dual feed. For AC systems, the operating input voltage is 180 to 305 VAC and for DC systems, the operating input voltage is 190 to 410 VDC.

The number of power feeds and whether the power supplies provide high output (30-A) or low output (20-A) power is configured using a set of dual inline package (DIP) switches on the faceplate of the power supply. If one power supply in the chassis is set to low power, the power budget for the chassis is reduced to low power, regardless of their DIP switch settings or the output results in CLI. This design safeguards against accidentally setting the power supply to 30-A in a facility that can only provide 20-A and tripping the facility circuit breaker. We recommend that you do not mix DIP switch settings in your system. See Table 3.

The JNP10K-PWR-AC2 power supplies share power.

The JNP10K-PWR-AC2 fits into the standard power supply bay but when compared to most other models, the JNP10K-PWR-AC2 is longer and protrudes from the bay when fully inserted into the chassis. See Figure 3 for the settings for the dip switches.

Figure 3: Comparision of the JNP10K-PWR-AC2 to the QFX10000-PWR-AC Power SupplyComparision of the JNP10K-PWR-AC2 to the QFX10000-PWR-AC Power Supply
Warning:

Extreme burn danger–Do not handle an HVAC or HVDC power supply running in the chassis without heat protective gloves, such as welder’s gloves. The JNP10K-PWR-AC2 can reach temperatures in the range of 158°F (70°C) to 176°F (80°C) under running conditions.

Warning:

The switch is pluggable type A equipment installed in a restricted-access location. It has a separate protective earthing terminal on the chassis that must be connected to earth ground permanently to ground the chassis adequately and protect the operator from electrical hazards.

CAUTION:

Before you begin installing the switch, ensure that a licensed electrician has attached an appropriate grounding lug to the grounding cable that you supply. Using a grounding cable with an incorrectly attached lug can damage the device.

CAUTION:

Use a 2-pole circuit breaker rated at 25 A in the building installation and the system, or as per local electrical code.
Table 3: Power Input and Output Voltages for JNP10K-PWR-AC2 Power Supplies

INP0 (Switch 1)

INP1 (Switch 2)

H/L (High Input 30 A/Low Input 20A)

Output Power

On

On

On (30 A)

5500 W

On

On

Off (20 A)

3000 W

On

Off

On (30 A)

5000 W

Off

On

On (30 A)

5000 W

On

Off

Off (20 A)

2700 W

Off

On

Off (20 A)

2700 W
CAUTION:

It is important to connect both input feeds of the JNP10K-PWR-AC2 power supply to AC mains before loading the system with power.

The JNP10K-PWR-AC2 requires the enhanced power bus to operate at full power. You can use the standard bus, but available power is 3000 W for power budget from the power management software. To determine whether your system has the standard power bus or the enhanced power bus, see QFX10000 Status Panel.

JNP10K-PWR-AC2 Power Specifications

The JNP10K-PWR-AC2 power supply supports AC, HVAC, and HVDC.

Table 4 lists the power specifications for the JNP10K-PWR-AC power supply.

Table 4: Power Specifications for a JNP10K-PWR-AC2 Power Supply

Item

Specifications

AC input voltage

180–305 VAC

DC input voltage

190–410  VDC

Input current rating

28.5 A

DC output power

12.3 V, 5500 W with dual feed and 5000 W with single feed

Table 5 shows the physical specifications for a JNP10K-PWR-AC2 power supply.

Table 5: Physical Specifications for a JNP10K-PWR-AC2 Power Supply

Specification

Value

Height

3.5 in. (8.89 cm)

Width

3.6 in. (9.14 cm)

Depth

15.1 in. (38.35 cm)

Weight

11.4 lb (5.17 kg)

QFX10000 Power Cables Specifications

Most sites distribute power through a main conduit that leads to frame-mounted power distribution panels, one of which can be located at the top of the rack that houses the switch. An AC power cord connects each power supply to the power distribution panel.

Each detachable AC power cord is 8 feet (approximately 2.5 meters) long. The coupler end of the appliance cord inserts into the AC appliance inlet on the faceplate of the AC power supply. The coupler type is C19 as described by the International Electrotechnical Commission (IEC) standard 60320. The plug end of the power cord fits into the power source outlet that is standard for your geographical location.

Note:

In North America, AC power cords must not exceed 15 feet (approximately 4.5 meters) in length, to comply with National Electrical Code (NEC) Sections 400-8 (NFPA 75, 5-2.2) and 210-52 and Canadian Electrical Code (CEC) Section 4-010(3). The cords shipped with the switch to North America and Canada are in compliance.

QFX10000 AC, high-voltage alternating current (HVAC), and high-voltage direct current (HVDC) have specific cord requirements. Use the following sections to determine the cable requirements based on the model of your power supply and any mode settings:

QFX10000-PWR-AC Power Cable Specifications

Table 6 lists the AC power cord specifications for QFX10000-PWR-AC for various countries and regions.

Table 6: AC Power Cord Specifications for QFX10000-PWR-AC Power Supplies

Country/Region

Electrical Specifications

Plug Standards

Juniper Model Number

Graphic

Argentina

250 VAC, 16 A, 50 Hz

IRAM Type RA/3/20

CBL-EX-PWR-C19-AR

Australia

250 VAC, 15 A, 50 Hz

AS/NZS 3112 Type SAA/3/15

CBL-EX-PWR-C19-AU

Brazil

250 VAC, 16 A, 50 Hz

NBR 14136: 2002 Type BR/3/20

CBL-EX-PWR-C19-BR

China

250 VAC, 16 A, 50 Hz

GB 1002 Type PRC/3/16

CBL-EX-PWR-C19-CH

Europe (except Italy, Switzerland, and United Kingdom)

250 VAC, 16 A, 50 Hz

CEE (7) VII Type VIIG

CBL-EX-PWR-C19-EU

India

250 AC, 16 A, 50 Hz

SABS 164/1:1992 Type ZA/3

CBL-EX-PWR-C19-SA

Israel

250 AC, 16 A, 50 Hz

SI 32/1971 Type IL/3

CBL-EX-PWR-C19-IL

Italy

250 VAC, 16 A, 50 Hz

CEI 23-16 Type I/3/16

CBL-EX-PWR-C19-IT

Japan

250 VAC, 16 A, 60 Hz

NEMA 6–20 Type N6/20

CBL-EX-PWR-C19-JP (default)

250 VAC, 16 A, 60 Hz

NEMA L6–20P Type NEMA Locking

CBL-EX-PWR-C19-JPL

Korea

250 VAC, 16 A, 50 Hz

CEE (7) VII Type VIIG

CBL-EX-PWR-C19-KR

North America

250 VAC, 16 A, 60 Hz

NEMA 6–20 Type N6/20

CBL-EX-PWR-C19-US (default)

250 VAC, 16 A, 60 Hz

NEMA L6–20P Type NEMA Locking

CBL-EX-PWR-C19-USL

South Africa

250 VAC, 16 A, 50 Hz

SABS 164/1:1992 Type ZA/3

CBL-EX-PWR-C19-SA

Switzerland

250 VAC, 16 A, 50 Hz

SEV 5934/2 Type 23G

CBL-EX-PWR-C19-SZ

United Kingdom

250 VAC, 13 A, 50 Hz

BS 1363/A Type BS89/13

CBL-EX-PWR-C19-UK

Worldwide (except Japan)

250 VAC, 16 A, 50 Hz

EN 60320-2-2/1

CBL-EX-PWR-C19-C20

JNP10K-PWR-AC2 Power Cable Specifications

The JNP10K-PWR-AC2 power supply operates in two modes:

Warning:

Do not run JNP10K-PWR-AC2 power supplies using 20-A cables if connected to 30-A input.
Table 7: JNP10K-PWR-AC2 Power Cable Specifications for 20-A Input

Locale

Cord Set Rating

Plug Standards

Spare Juniper Model Number

Graphic

Argentina

16 A, 250 VAC

IRAM 2073 Type RA/3

CBL-JNP-SG4-AR

Australia and New Zealand

15 A, 250  VAC

AS/NZS 4417

CBL-JNP-SG4-AU

Brazil

16 A, 250 VAC

NBR 14136 Type BR/3

CBL-JNP-SG4-BR

China

16 A, 250 VAC

GB2099

CBL-JNP-SG4-CH

Europe (except Italy, Switzerland, and United Kingdom)

20 A, 250 VAC

IEC 316P6W

CG_CBL-APP-400-02

Great Britain

13 A, 250 VAC,

BS1363

CBL-JNP-SG4-UK

India

16 A, 250 VAC

SANS 164/1

CBL-JNP-SG4-SA

Israel

16 A, RA, 250 VAC

SI 32/1971 Type IL/3G

CBL-JNP-SG4-IL

Italy

16 A, 250 VAC

CEI 23-16

CBL-JNP-SG4-IT

North America

20 A, 250 VAC

C20 to Anderson 3-5958p4

CBL-JNP-SG4-C20

North America

16 A, 250 VAC

Locking NEMA L6-20P

CBL-JNP-SG4-US-L

North America

16 A, 250 VAC

NEMA 6-20P

CBL-JNP-SG4-US

North America

20 A, 250 V

IEC 320P6W

CG_CBL-APP-400-02

South Africa

16 A, 250 VAC

SANS 164/1

CBL-JNP-SG4-SA

Switzerland

16 A, 250 VAC

CEI 23-50

CBL-JNP-SG4-SZ
Table 8: JNP10K-PWR-AC2 Power Cable Specifications for HVAC Input

Locale

Cord Set Rating

Plug Standards

Spare Juniper Model Number

Graphic

North America

16 A, 277 V

NEMA L7-20P

CBL-JNP-SG4-HVAC

JNP10K-PWR-AC2 Power Cable Specifications for 30-A Input

The JNP10K-PWR-AC2 HVAC or HVDC power supplies requires a high voltage cable assembly when set for 30-A input. One end of the cable has an Anderson APP-400 connector, the other end of the cable is bare wire. See Figure 4 and Table 9. These cables are separately orderable and are not shipped automatically with JNP10K-PWR-AC2 orders. An example of the right-angle cable and connector is shown in Figure 6.

For connection to AC systems, Juniper provides a cable with either a NEMA 30-A connector (Figure 4) or an IEC 330P6W connector (Figure 5).

Figure 4: NEMA 30-A ConnectorNEMA 30-A Connector
Figure 5: IEC 330P6W ConnectorIEC 330P6W Connector
Table 9: 30-A Cabling Options

Power Cord

Locale

Cord Set Rating

Plug Standards

Connector

Spare Juniper Model Number

HVDC power cord

Any

30- A, 400 VAC

UL 950 and IEC 60950

Anderson/straight to bare wire

CBL-PWR2-BARE

HVDC power cord

Any

30-A, 400 VAC

UL 950 and IEC 60950

Anderson/right-angle to bare wire

CBL-PWR2-BARE-RA

AC power cord

Continental Europe

30-A 250 VAC

UL 950 and IEC332P6

Anderson/straight to IEC 332P6

CBL-PWR2-332P6W-RA

AC power cord

North America

30-A 250 VAC

UL 950 and IEC332P6

Anderson/straight to IEC332P6

CBL-PWR2-332P6W

AC power cord

North America

30-A 240 VAC

IEC330P6

Anderson/right-angle to IEC 330P6

CBL-PWR2-330P6W-RA

AC power cord

North America

30-A 240 VAC

IEC330P6

Anderson/straight to IEC 330P6

CBL-PWR2-330P6W

AC power cord

North America

30-A 250 VAC

UL 498, IEC5958P4

Anderson/straight to L6-30P

CBL-PWR2-L6-30P

AC jumper power cord

North America

30-A 400 VAC

UL, CSA

Anderson/straight to Anderson

CG-CBL-APP-400-02

AC power cord

North America

30-A 250 VAC

UL 498, CSA

Anderson/right-angle to L6-30P

CBL-PWR2-L6-30P-RA
Figure 6: Right-Angle, Bare Cable with Anderson ConnectorRight-Angle, Bare Cable with Anderson Connector
  1
—

Black wire–Return (+)

  3
—

White wire–Neutral

  2
—

Green wire-Ground

 

See Also

QFX10000 AC Power Supply LEDs

The QFX10000-PWR-AC power supply has four LEDs on its faceplate: INP1, INP2, PWR OK, and FAULT. These LEDs display information about the status of the power supply. See Figure 7.

Figure 7: LEDs on a QFX10000-PWR-AC, Power Supply in QFX10000 SwitchesLEDs on a QFX10000-PWR-AC, Power Supply in QFX10000 Switches
  1
—

FAULT

  3
—

INP2–Source input 2

  2
—

PWR OK

  4
—

INP1–Source input 1

Table 10 describes the LEDs on a QFX10000-AC power supply in QFX10008 and QFX10016 modular chassis.

Table 10: LEDs on a QFX10000-AC Power Supply in a QFX10000

LED

Color

State

Description

INP1 (INP0 in CLI output) or INP2 (INP1 in CLI output)

Yellow

Blinking

Indicates that the AC power input voltage is not within normal operating range.

Green

Solid

AC is within operating range (200–240 VAC).

Dark

Unlit

The power supply is switched off.

PWR OK

Green

Solid

DC power output is within normal operating range.

Yellow

Blinking

The output is out of the limits.

FAULT

Dark

Unlit

Power supply is functioning normally.

Red

Solid

Power supply has failed and must be replaced. Or, only one input is powered and the enabled switch for the input that is not powered is set to ON. See Connect AC Power to a QFX Modular Chassis for more information about the enable switches.
Note:

If the INP1 or INP2 LED and the PWR OK LED are unlit, the AC power cord is not installed properly or the power supply has failed.

If the INP1 or INP2 LED is lit and the PWR OK LED is unlit, the AC power supply is not installed properly or the power supply has an internal failure.

See Also

JNP10K-PWR-AC2 Power Supply LEDs

The JNP10K-PWR-AC2 power supply has four LEDs on its faceplate: !, OK, 2, and 1. These LEDs display information about the status of the power supply. See Figure 8.

Figure 8: LEDs on a JNP10K-PWR-AC2 HVAC/HVDC Power Supply LEDs on a JNP10K-PWR-AC2 HVAC/HVDC Power Supply
  1
—

! FAULT

  3
—

2 INP2–Source input 1

  2
—

OK PWR OK

  4
—

1 INP1–Source input 0
Note:

Physical markings on the power supply are INP1 and INP2. These markings correspond to INP0 and INP1 in the show chassis power output (see Table 11).
Table 11: Physical Markings on Chassis Versus Show Chassis Power Command

Physical Marking on JNP10K-PWR-AC2

Show Chassis Power Command

INP1

INP0

INP2

INP1

Table 12 describes the LEDs on a JNP10K-PWR-AC2 power supply.

Table 12: Interpreting JNP10K-PWR-AC2 LEDs

LED

Color

State

Description

INP1 or INP0 in CLI output

Yellow

Blinking

The input voltage is present, but is not within normal operating range.

Green

Solid

The input voltage is present and within normal operating range.

Unlit

Off

The power supply is switched off; voltage is zero.

INP2 or INP1 in CLI output

Yellow

Blinking

The input voltage is present, but is not within normal operating range.

Green

Solid

The input voltage is present and within normal operating range.

Unlit

Off

The power supply is switched off; voltage is zero.

OK

Green

Solid

The power supply output is within normal operating range.

Yellow

Blinking

The power supply output is out of the power limits or is over-current position.

!

Red

Solid

Power supply has failed and must be replaced.

Unlit

Off

Power supply is functioning normally.

Related Documentation