Understanding VLAN Manipulation (Normalization and VLAN Mapping) on Ethernet Services

VLAN Translation (Normalization) for E-LAN Services

A packet received on a physical port is only accepted for processing if the VLAN tags of the received packet match the VLAN tags associated with one of the logical interfaces configured on the physical port. The VLAN tags of the received packet are translated only if they are different than the normalized VLAN tags. For the translation case, the VLAN identifier tags specify the normalized VLAN.

The VLAN tags of a received packet are compared with the normalized VLAN tags specified with either the vlan-id or vlan-tags statements. If the VLAN tags of the received packet are different from the normalized VLAN tags, then appropriate VLAN tag operations (such as push-push, pop-pop, pop-swap, swap-swap, swap, and others) are implicitly made to convert the received VLAN tags to the normalized VLAN tags. Then, the source MAC address of a received packet is learned based on the normalized VLAN configuration. For output packets, if the VLAN tags associated with an egress logical interface do not match the normalized VLAN tags within the packet, then appropriate VLAN tag operations (such as push-push, pop-pop, pop-swap, swap-swap, swap, and others) are implicitly made to convert the normalized VLAN tags to the VLAN tags for the egress logical interface. For more information about these operations, see the Junos OS Routing Protocols Configuration Guide.

VLAN Mapping for VPLS Services

For Ethernet services and Ethernet services with flexible VLAN tagging (asymmetric tag depth), the Connectivity Services Director application uses the VLAN configuration data that you specified in the service order to apply the appropriate VLAN tags to the input and output VLAN maps for the ingress and egress logical interfaces, respectively. The following steps outline the process of bridging a packet received over a Layer 2 logical interface when a normalizing VLAN identifier (vlan-id number or vlan-tags statement) is specified for a bridge domain or VPLS routing instance:

1. When a packet is received on a physical port, it is accepted only if the VLAN identifier of the packet matches the VLAN identifier of one of the logical interfaces configured on that port.

2. The VLAN tags of the received packet are then compared with the normalizing VLAN identifier. If the VLAN tags of the packet are different from the normalizing VLAN identifier, the VLAN tags are rewritten, as described in Table 1.

3. If the source MAC address of the received packet is not present in the source MAC table, it is learned based on the normalizing VLAN identifier.

4. The packet is then forwarded toward one or more outbound Layer 2 logical interfaces based on the destination MAC address. A packet with a known unicast destination MAC address is forwarded only to one outbound logical interface. For each outbound Layer 2 logical interface, the normalized VLAN identifier configured for the bridge domain or VPLS routing instance is compared with the VLANs tags that are configured on that logical interface. If the VLAN tags associated with an outbound logical interface do not match the normalizing VLAN identifier that is configured for the bridge domain or VPLS routing instance, the VLAN tags are rewritten, as described in Table 2.

Table 1 and Table 2 show how VLAN tags are applied when traffic is sent to and from the bridge domain, depending on how the VLAN IDs and VLAN tags (inner and outer) are configured for the bridge domain and on how VLAN identifiers are configured for the logical interfaces in a bridge domain or VPLS routing instance. Depending on the configuration of the Ethernet services that you create in Connectivity Services Director, the following rewrite operations are performed on VLAN tags:

• pop—Remove the VLAN tag from the top of the VLAN tag stack.

• pop/pop—Remove both the outer and inner VLAN tags of the frame.

• pop/swap—Remove the outer VLAN tag of the frame and replace the inner VLAN tag of the frame.

• swap—Replace the inner VLAN tag of the frame.

• push—Add a new VLAN tag to the top of the VLAN stack.

• push/push—Push two VLAN tags in front of the frame.

• swap/push—Replace the VLAN tag of the frame and add a new VLAN tag to the top of the VLAN stack.

• swap/swap—Replace both the outer and inner VLAN tags of the frame.

No operation means that the VLAN tags of the inbound or outbound packet are not translated for the specified output logical interface or input logical interface.NA means not applicable.

Sample VLAN Configuration on MX Series and M Series PE Routers

MX Series devices can use VLAN mapping or normalization to translate VLANs tags. M Series devices use only VLAN mapping to translate VLAN tags. The following sample configurations show the VLAN and VPLS routing-instance configurations for an MX960 PE interface and M320 PE interface.

interfaces {			
	ge-0/0/0 {
   	unit 1 {    
            encapsulation vlan-vpls;
            vlan-tags outer 5 inner 5;
##normalizing the inner and outer tags towards the core with Push/Push operations##           
	family vpls
		}
			}
				}
   

interfaces {			
	ge-1/1/1 {
   	unit 1 {    
            encapsulation vlan-vpls;
            vlan-tags outer 22 inner 2;
## Q-in-Q tags configured on the PE interface ##         
input-vlan-map {
swap-swap;
##normalizing the inner and outer tags towards the core by swapping both tags##
		vlan-id 2;
		inner-vlan-id 1;
		}
	output-vlan-map swap-swap; 
## Put the original tags back for the packets towards the VPLS CE ##		
		family vpls
	}
		}
			}