Prerequisites for Installing JSA 7.5.0 Update Package 1 qcow2

Before you begin, see section Administrator Notes to understand the system requirements for installing JSA 7.5.0 Update Package 1 using an qcow2 image.

We recommend that you increase the amount of storage allocated to a particular partition on the disk image.

Perform the following steps to expand the disk image or store partition:

Note:

Shut down the VM before you perform this operation to avoid corrupting the disk that contains the qcow2 image.

Expand the qcow2 disk image by using the following command.

Check if there is sufficient disk space for the uncompressed image by using the following command.

Boot the disk image by using the following command.
Log in as the root user to JSA by using the JSA console or SSH.

Run the parted command on the disk /dev/vda to increase the size of the disk partition. Ensure that you type fix when prompted.

Reboot the device so that the new partition is reflected in the partition table by using the following command.

Run the parted command to display the free space and note the beginning and ending blocks.

Reboot the device to ensure that the new partition fixes are reflected in the partition table.

Create a new partition at the end of the existing partition by using the following commands.

Set the partition as a Logical Volume Manager (LVM) partition by using the following commands.

Table 1 shows the updated partition table after creating an LVM partition.

Table 1: Partition Table Information
Number	Start	End	Size	File System	Name Flags
	34s	2047s	2014s	Free Space
1	2048s	4095s	2048s		bios_grub
2	4096s	2101247s	2097152s	xfs
3	2101248s	69210111s	67108864s	xfs
4	69210112s	882888703s	813678592s		lvm

Quit the parted command and add the new LVM partition as a physical volume to LVM by using the following command.

Table 2 shows the LVM partition added as a physical volume.

Table 2: Adding LVM Partition as a Physical Volume
PV	VG	Fmt	Attr	PSize	PFree
/dev/vda4	storerhel	lvm2	a--	<387.99g	0
/dev/vda5	rootrhel	lvm2	a--	67.00g	0

Extend the physical volume group by using the following command.

The physical volume group is now extended.

Use the following command to extend the logical volume of the disk.

Table 3: File System Information
File system	Size	Used	Available	Use %	Mounted on
/dev/mapper/rootrhel-root	13 Gb	3.0 Gb	9.5 Gb	24%	/
devtmpfs	32 Gb	0	32 Gb	0%	/dev
tmpfs	32 Gb	20 Kb	32 Gb	1%	/dev/shm
tmpfs	32 Gb	34 Mb	32 Gb	1%	/run
tmpfs	32 Gb	0	32 Gb	0%	/sys/fs/cgroup
/dev/mapper/rootrhel-tmp	3.0 Gb	135 Mb	2.9 Gb	5%	/tmp
/dev/vda3	32 Gb	4.8 Gb	28 Gb	15%	/recovery
/dev/mapper/storerhel-store	311 Gb	21 Gb	290 Gb	7%	/store
/dev/mapper/rootrhel-opt	13 Gb	4.3 Gb	8.3 Gb	34%	/opt
/dev/mapper/rootrhel-home	1014 Mb	33 Mb	982 Mb	4%	/home
tm/dev/mapper/rootrhel-storetmp	15 Gb	44 Mb	15 Gb	1%	/storetmp
/dev/mapper/storerhel-transient	78 Gb	34 Mb	78 Gb	1%	/transient

The logical volume is now extended.

Extend the file system by using the following command.
The file system is now extended.

You have now extended the physical volume group, logical volume of the disk, and the file system as required. You can now install JSA 7.5.0 Update Package 1 using a qcow2 image. See Installing JSA 7.5.0 Update Package 1 qcow2 on the KVM for information on installing JSA 7.5.0 Update Package 1 using a qcow2 image.