Rate and give feedback:  Feedback Received. Thank You!

Rate and give feedback: 

X

This document helped resolve my issue

Yes No

Additional Comments

800 characters remaining

May we contact you if necessary?

Name:  

E-mail: 

Enter a valid Email ID

Need product assistance? Contact Juniper Support

Submit

This site is protected by hCaptcha and its Privacy Policy and Terms of Service apply.

English  

English

Example: Configuring BFD for OSPF

Requirements

Before you begin:

• Configure the device interfaces. See the Junos® OS Network Interfaces.
• Configure the router identifiers for the devices in your OSPF network. See Example: Configuring an OSPF Router Identifier.
• Control OSPF designated router election. See Example: Controlling OSPF Designated Router Election.
• Configure a single-area OSPF network. See Example: Configuring a Single-Area OSPF Network.
• Configure a multiarea OSPF network. See Example: Configuring a Multiarea OSPF Network.
• Configure a multiarea OSPF network. See Example: Configuring a Multiarea OSPF Network.

Overview

An alternative to adjusting the OSPF hello interval and dead interval settings to increase route convergence is to configure BFD. The BFD protocol is a simple hello mechanism that detects failures in a network. The BFD failure detection timers have shorter timer limits than the OSPF failure detection mechanisms, thereby providing faster detection.

BFD is useful on interfaces that are unable to detect failure quickly, such as Ethernet interfaces. Other interfaces, such as SONET interfaces, already have built-in failure detection. Configuring BFD on those interfaces is unnecessary.

You configure BFD on a pair of neighboring OSPF interfaces. Unlike the OSPF hello interval and dead interval settings, you do not have to enable BFD on all interfaces in an OSPF area.

• full-neighbors-only—In Junos OS Release 9.5 and later, configures the BFD protocol to establish BFD sessions only for OSPF neighbors with full neighbor adjacency. The default behavior is to establish BFD sessions for all OSPF neighbors.
• minimum-interval—Configures the minimum interval, in milliseconds, after which the local routing device transmits hello packets as well as the minimum interval after which the routing device expects to receive a reply from the neighbor with which it has established a BFD session. You can configure a number in the range from 1 through 255,000 milliseconds. You can also specify the minimum transmit and receive intervals separately using the transmit-interval minimum-interval and minimum-receive-interval statements.

  Note: BFD is an intensive protocol that consumes system resources. Specifying a minimum interval for BFD of less than 100 ms for Routing Engine-based sessions and 10 ms for distributed BFD sessions can cause undesired BFD flapping. Depending on your network environment, these additional recommendations might apply: For large-scale network deployments with a large number of BFD sessions, specify a minimum interval of 300 ms for Routing Engine-based sessions and 100 ms for distributed BFD sessions. For very large-scale network deployments with a large number of BFD sessions, contact Juniper Networks customer support for more information. For BFD sessions to remain up during a Routing Engine switchover event when nonstop active routing (NSR) is configured, specify a minimum interval of 2500 ms for Routing Engine-based sessions. For distributed BFD sessions with NSR configured, the minimum interval recommendations are unchanged and depend only on your network deployment.

• multiplier—Configures the number of hello packets not received by a neighbor that causes the originating interface to be declared down. By default, three missed hello packets cause the originating interface to be declared down. You can configure a value in the range from 1 through 255.

Configuration

CLI Quick Configuration

To quickly configure the BFD protocol for OSPF, copy the following commands, remove any line breaks, and then paste the commands into the CLI.

Step-by-Step Procedure

1. Create an OSPF area.

   Note: To specify OSPFv3, include the ospf3 statement at the [edit protocols] hierarchy level.

   [edit]user@host# edit protocols ospf area 0.0.0.0
2. Specify the interface.
   [edit protocols ospf area 0.0.0.0]user@host# set interface fe-0/0/1
3. Specify the minimum transmit and receive intervals.
   [edit protocols ospf area 0.0.0.0 ]user@host# set interface fe-0/0/1 bfd-liveness-detection minimum-interval 300
4. Configure the number of missed hello packets that cause the originating interface to be declared down.
   [edit protocols ospf area 0.0.0.0 ]user@host# set interface fe-0/0/1 bfd-liveness-detection multiplier 4
5. Configure BFD sessions only for OSPF neighbors with full neighbor adjacency.
   [edit protocols ospf area 0.0.0.0 ]user@host# set interface fe-0/0/1 bfd-liveness-detection full-neighbors-only
6. If you are done configuring the device, commit the configuration.
   [edit protocols ospf area 0.0.0.0 ]user@host# commit

   Note: Repeat this entire configuration on the other neighboring interface.

Results

Confirm your configuration by entering the show protocols ospf command. If the output does not display the intended configuration, repeat the instructions in this example to correct the configuration.

To confirm your OSPFv3 configuration, enter the show protocols ospf3 command.

Verification

Confirm that the configuration is working properly.

Verifying the BFD Sessions

Purpose

Verify that the OSPF interfaces have active BFD sessions, and that session components have been configured correctly.

Action

From operational mode, enter the show bfd session detail command.

Meaning

The output displays information about the BFD sessions.

• The Address field displays the IP address of the neighbor.
• The Interface field displays the interface you configured for BFD.
• The State field displays the state of the neighbor and should show Full to reflect the full neighbor adjacency that you configured.
• The Transmit Interval field displays the time interval you configured to send BFD packets.
• The Multiplier field displays the multiplier you configured.