close

keyboard_arrow_left

Table of Contents Expand all

play_arrow Fast Track: Initial Installation
- Fast Track to Rack Installation and Power
- Onboard and Configure SRX4100
play_arrow Overview
play_arrow Site Planning, Preparation, and Specifications
play_arrow Initial Installation and Configuration
play_arrow Maintaining Components
play_arrow Troubleshooting Hardware
- Troubleshooting the SRX4100
play_arrow Contacting Customer Support and Returning the Chassis or Components
- Returning the SRX4100 Chassis or Components
play_arrow Safety and Compliance Information

list Table of Contents

English

Connecting the SRX4100 to Power

date_range 11-Sep-24

arrow_backward

arrow_forward

Connecting the SRX4100 Firewall Grounding Cable

To meet safety and electromagnetic interference (EMI) requirements and to ensure proper operation, the services gateway must be adequately grounded before power is connected. You must provide a grounding lug to connect the services gateway to earth ground.

You ground the services gateway by connecting a grounding cable to earth ground and then attaching it to the chassis grounding point located on the back panel of the device using an M5 x 10 mm grounding screw.

You must install the SRX4100 in a restricted-access location and ensure that the chassis is always properly grounded. The SRX4100 has a single-hole protective grounding terminal provided on the chassis. See Figure 1. Under all circumstances, use this grounding connection to ground the chassis. For AC-powered systems, you must also use the grounding wire in the AC power cord along with the single-hole grounding lug connection. This tested system meets or exceeds all applicable EMC regulatory requirements with the single-hole protective grounding terminal.

CAUTION:

Before you connect power to the services gateway, a licensed electrician must attach a cable lug to the grounding cable that you supply. A cable with an incorrectly attached lug can damage the services gateway (for example, by causing a short circuit).

Ensure that you have the following parts and tools available:

Electrostatic discharge (ESD) grounding wrist strap
Phillips (+) screwdriver, number 2
16 AWG single-strand wire grounding cable (green and yellow wire)
Grounding lug (ring-type, vinyl-insulated TV14-6R lug, or equivalent)
One metric M5 x 10 mm grounding screw

To connect the services gateway to earth ground:

Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis.
Connect one end of the grounding cable to a proper earth ground, such as the rack in which the services gateway is mounted.
Place the grounding lug attached to the grounding cable over the grounding point.
Secure the grounding cable lug to the grounding point with the screw. See Figure 1.
Figure 1: Connecting the Grounding Cable
Dress the grounding cable and verify that it does not touch or block access to the services gateway components and that it does not drape where people could trip on it.

Note:

When removing the chassis, turn off the power, and disconnect the grounding cable.

Connecting AC Power to an SRX4100 Firewall

Ensure that you have a power cord appropriate for your geographical location available to connect AC power to an SRX4100 Firewall. Before you begin connecting AC power:

Ensure that you have taken the necessary precautions to prevent electrostatic discharge (ESD) damage.
Ensure that you have connected the device chassis to earth ground.

CAUTION:
Before you connect power to the services gateway, a licensed electrician must attach a cable lug to the grounding cable that you supply. A cable with an incorrectly attached lug can damage the device (for example, by causing a short circuit).

To meet safety and electromagnetic interference (EMI) requirements and to ensure proper operation, you must properly ground the services gateway chassis before connecting power.

To connect AC power:

Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the rear of the chassis.
Ensure that the power supplies are fully inserted in the chassis and the latches are secure.
Locate the power cords shipped with the services gateway; the cords have plugs appropriate for your geographical location.
Insert the coupler end of the power cord into the AC power cord inlet on the AC power supply faceplate.
Push the power cord retainer onto the power cord. See Figure 2.
Figure 2: Connecting AC Power
If the AC power source outlet has a power switch, set it to the off (0) position.
Insert the power cord plug into an AC power source outlet.
Dress the power cord appropriately. Verify that the power cord does not block the air exhaust and access to services gateway components or drape where people could trip on it.
If the AC power source outlet has a power switch, set it to the on (|) position.
Repeat steps 4 through 8 for the second AC power supply.
Verify that the AC and DC LEDs on each power supply are lit green. If the fault status (!) LED is lit amber, remove power from the power supply, and replace the power supply (see Removing an AC Power Supply from an SRX4100 Services Gateway). Do not remove the power supply until you have a replacement power supply ready. The power supplies must be installed in the services gateway to ensure proper airflow.

Connecting DC Power to an SRX4100 Firewall

Before you begin connecting DC power to an SRX4100 Firewall:

Ensure that you have taken the necessary precautions to prevent electrostatic discharge (ESD) damage.
Ensure that you have connected the chassis to earth ground.

CAUTION:
Before you connect power to the services gateway, a licensed electrician must attach a cable lug to the grounding cable that you supply. A cable with an incorrectly attached lug can damage the device (for example, by causing a short circuit).

To meet safety and electromagnetic interference (EMI) requirements and to ensure proper operation, you must properly ground the services gateway chassis before connecting power.

Ensure that you have the following parts and tools available:

DC power source cables (14–16 AWG) with ring lug (Molex 190700069 or equivalent)
Phillips (+) screwdriver, number 2
Multimeter

To connect DC power:

Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the rear of the chassis.
Verify that the DC power cables are correctly labeled before making connections to the power supply. In a typical power distribution scheme where the return is connected to chassis ground at the battery plant, you can use a multimeter to verify the resistance of the -48V and RTN DC cables to chassis ground.
- The cable with very high resistance (indicating an open circuit) to chassis ground is negative (–) and will be installed on the V– (input) DC power input terminal.
- The cable with very low resistance (indicating a closed circuit) to chassis ground is positive (+) and will be installed on the V+ (return) DC power input terminal.
CAUTION:
You must ensure that power connections maintain the proper polarity. The power source cables might be labeled (+) and (–) to indicate their polarity. There is no standard color coding for DC power cables. The color coding used by the external DC power source at your site determines the color coding for the leads on the power cables that attach to the terminal studs on each power supply.
Ensure that the input circuit breaker is open so that the voltage across the DC power source cable leads is 0 V and that the cable leads will not become active while you are connecting DC power.
Install heat-shrink tubing insulation around the power cables:
1. Slide the tubing over the portion of the cable where it is attached to the lug barrel. Ensure that the tubing covers the end of the wire and the barrel of the lug attached to it.
2. Shrink the tubing with a heat gun. Ensure that you heat all sides of the tubing evenly so that it shrinks around the cable tightly.
  
  Note:
  Do not overheat the tubing.
  
  Figure 3 shows how to install heat-shrink tubing.
  
  Figure 3: How to Install Heat-Shrink Tubing
Remove the terminal block cover. The terminal block cover is a piece of clear plastic that snaps into place over the terminal block.
Remove the screws on the terminals using the screwdriver.
Secure each positive (+) DC source power cable lug to a RTN (return) terminal. Secure each negative (–) DC source power cable lug to a -48V (input) terminal.
Figure 4: Connecting DC Power
Tighten the screws on the power supply terminals until snug using the screwdriver. Do not overtighten.
Replace the terminal block cover.
Close the input circuit breaker.
The device powers on as soon as power is provided to the power supply.
Verify that the IN and OUT LEDs on the power supply are lit green and are on steadily.

arrow_backward PREVIOUS Unpacking and Mounting the SRX4100

NEXT arrow_forward Connecting the SRX4100 Firewall to a Management Console

SRX4100 Firewall Hardware Guide

ON THIS PAGE

Connecting the SRX4100 to Power

Connecting the SRX4100 Firewall Grounding Cable

Connecting AC Power to an SRX4100 Firewall

Connecting DC Power to an SRX4100 Firewall

Stay in touch

Helped me install or use the product
Accelerated my deployment

Discuss the product with a co-worker
Make a purchase inquiry

SRX4100 Firewall Hardware Guide

ON THIS PAGE

Connecting the SRX4100 to Power

Connecting the SRX4100 Firewall Grounding Cable

Connecting AC Power to an SRX4100 Firewall

Connecting DC Power to an SRX4100 Firewall

Related Documentation

Stay in touch