- play_arrow Fast Track: Initial Installation
- play_arrow Overview
- play_arrow Initial Installation and Configuration
- play_arrow Maintaining Components
- play_arrow Troubleshooting Hardware
- play_arrow Contacting Customer Support and Returning the Chassis or Components
- play_arrow Safety and Compliance Information
- General Safety Guidelines and Warnings
- Definitions of Safety Warning Levels
- Restricted Access Area Warnings
- Qualified Personnel Warning
- Prevention of Electrostatic Discharge Damage
- Fire Safety Requirements
- Laser and LED Safety Guidelines and Warnings
- Radiation from Open Port Apertures Warning
- Maintenance and Operational Safety Guidelines and Warnings
- General Electrical Safety Guidelines and Warnings
- AC Power Electrical Safety Guidelines
- DC Power Electrical Safety Guidelines
- DC Power Disconnection Warning
- DC Power Grounding Requirements and Warning
- DC Power Wiring Sequence Warning
- DC Power Wiring Terminations Warning
- Action to Take After an Electrical Accident
- Agency Approvals
- Acoustic Noise Compliance Statements
- EMC Requirements
SRX4100 Transceiver Specifications and Pinouts
Pluggable Transceivers Supported on SRX4100 Services Gateways
The ports on the SRX4100 Firewall supports SFP+ transceivers. The following are the transceivers supported on the services gateway:
EX-SFP-1GE-T
EX-SFP-10GE-ER
SRX-SFP-10GE-ER
SRX-SFP-10GE-LR
SRX-SFP-10GE-SR
JNP-10G-SR-8PACK
SRX-SFP-1GE-LH
SRX-SFP-1GE-LX
SRX-SFP-1GE-SX
JNP-1G-SX-8PACK
SRX-SFP-1GE-T
Note:The SRX4100 Firewall supports only 1000 Mbps speed on SRX-SFP-1GE-T and EX-SFP-1GE-T; 10-Mbps and 100-Mbps speeds are not supported.
JNP-1G-T-8PACK
For the full specifications of these transceivers, see The Hardware Compatibility Tool.
When using 1-gigabit transceivers, the name of the interface
follows the convention xe-0/0/port-number but the interface operates at 1-Gbps speed.
SFP+ Direct Attach Copper Cables for SRX4100 Services Gateways
Small form-factor pluggable plus transceiver (SFP+) direct attach copper (DAC) cables are suitable for short distances of up to 23 ft (7 m), making them ideal for highly cost-effective networking connectivity within a rack and between adjacent racks. The SRX4100 Firewall supports the following 1 m and 3 m long DAC cables:
SRX-SFP-10GE-DAC-1M
SRX-SFP-10GE-DAC-3M
For the full specifications of these transceivers, see The Hardware Compatibility Tool.
Management Port Connector Pinout Information for an SRX4100 Services Gateway
The port on the front panel labeled MGMT is an autosensing 10/100/1000-Mbps Ethernet RJ-45 receptacle that accepts an Ethernet cable for connecting the services gateway to a management LAN (or other device that supports out-of-band management). Two LEDs on the port indicate link activity on the port and the administrative status of the port.
Table 1 provides the pinout information for the RJ-45 connector for the management port. An RJ-45 cable, with a connector attached, is supplied with the services gateway.
Pin | Signal |
|---|---|
1 | TX+ |
2 | TX- |
3 | RX+ |
4 | Termination network |
5 | Termination network |
6 | RX- |
7 | Termination network |
8 | Termination network |
Console Port Connector Pinout Information for an SRX4100 Services Gateway
The console port is an RS-232 serial interface that uses an RJ-45 connector to connect to a console management device. The default baud rate for the console port is 9600 baud.
Table 2 provides the pinout information for the RJ-45 console connector. An Ethernet cable that has an RJ-45 connector at either end and an RJ-45 to DB-9 serial port adapter are supplied with the services gateway.
Pin | Signal | Description |
|---|---|---|
1 | RTS | Request to Send |
2 | DTR | Data Terminal Ready |
3 | TXD | Transmit Data |
4 | Ground | Signal Ground |
5 | Ground | Signal Ground |
6 | RXD | Receive Data |
7 | DSR/DCD | Data Set Ready |
8 | CTS | Clear to Send |
