Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 
 

SRX345 Power System

SRX345 Firewall Power Supply

The SRX345 Firewall is available with either a single AC power supply (Junos OS Release 15.1X49-D35 and later), dual AC power supplies (Junos OS Release 15.1X49-D110 and later), or a single DC power supply (Junos OS Release 17.4R1 and later). The power supply distributes the different output voltages to the device components according to their voltage requirements. The power supply is fixed in the chassis and is not a field-replaceable unit.

To identify the SRX345 model, check the Description field in the output of the show chassis hardware command.

The following are sample outputs for the different SRX345 models.

  • SRX345 with single AC power supply

  • SRX345 with single DC power supply

  • SRX345 with dual AC power supplies

    If one power supply on an SRX345 (with dual AC power supplies) fails, the remaining power supply redistributes the electrical load without interruption.

SRX345 Firewall Power Specifications and Requirements

The AC power system electrical specifications for the SRX345 Firewall are listed in Table 1.

Table 1: Power System Electrical Specifications for the SRX345 Firewall (AC Models)

Power Requirement

Specification

AC input voltage

100 to 240 VAC

AC input line frequency

50 to 60 Hz

AC system current rating

1 to 1.5 A

Maximum AC inrush current

7.3 A at 220 V/50 Hz (with four Mini-PIMs installed)

Warning:

The AC power cord for the services gateway is intended for use with the device only and not for any other use.

The DC power system electrical specifications for the SRX345 Firewall are listed in Table 2.

Table 2: Power System Electrical Specifications for the SRX345 Firewall (DC Model)

Power Requirement

Specification

Rated DC voltage range

–48 to –60 VDC (with -15% and +20% tolerance)

Operating voltage range –40.8 to –72 VDC

DC system current rating

6 A at –48 VDC

DC output

12 V@150W

SRX345 Firewall Supported AC Power Cords

Warning:

The AC power cord for the services gateway is intended for use with the services gateway only and not for any other use.

Note:

In North America, AC power cords must not exceed 4.5 m (approximately 14.75 ft) in length, to comply with National Electrical code (NEC) Section 400-8 (NFPA 75, 5-2.2) and 210-52, and Canadian Electrical Code (CEC) Section 4-010(3).

Table 3 provides power cord specifications, and Figure 1 depicts the plug on the AC power cord provided for each country or region.

Table 3: AC Power Cord Specifications

Country

Electrical Specification

Plug Standards

Australia

250 VAC, 10 A, 50 Hz

AS/NZ 3112-1993

China

250 VAC, 10 A, 50 Hz

GB2099.1 1996 and GB 1002 1996 (CH1-10P)

Europe (except Italy and United Kingdom)

250 VAC, 10 A, 50 Hz

CEE (7) VII

Italy

250 VAC, 10 A, 50 Hz

CEI 23-16/VII

Japan

125 VAC, 12 A, 50 or 60 Hz

JIS 8303

North America

125 VAC, 10 A, 60 Hz

NEMA 5-15

United Kingdom

250 VAC, 10 A, 50 Hz

BS 1363A

Figure 1: AC Plug TypesAC Plug Types
Note:

Power cords and cables must not block access to services gateway components or drape where people might trip on them.