- play_arrow Port Security
- play_arrow Port Security Overview
-
- play_arrow IPSec
- play_arrow Understanding IPsec and Security Associations
- play_arrow IPsec Configurations and Examples
- play_arrow Configuring IPsec Security Associations
- play_arrow Using Digital Certificates for IPsec
- play_arrow Additional IPsec Options
- play_arrow Configuring IPsec Dynamic Endpoints
- play_arrow Additional ES and AS PIC Configuration Examples
- Example: ES PIC Manual SA Configuration
- Example: AS PIC Manual SA Configuration
- Example: ES PIC IKE Dynamic SA Configuration
- Example: AS PIC IKE Dynamic SA Configuration
- Example: IKE Dynamic SA Between an AS PIC and an ES PIC Configuration
- Example: AS PIC IKE Dynamic SA with Digital Certificates Configuration
- Example: Dynamic Endpoint Tunneling Configuration
-
- play_arrow Digital Certificates
- play_arrow Configuring Digital Certificates
- Public Key Cryptography
- Configuring Digital Certificates
- Configuring Digital Certificates for an ES PIC
- IKE Policy for Digital Certificates on an ES PIC
- Configuring Digital Certificates for Adaptive Services Interfaces
- Configuring Auto-Reenrollment of a Router Certificate
- IPsec Tunnel Traffic Configuration
- Tracing Operations for Security Services
- play_arrow Configuring SSH and SSL Router Access
-
- play_arrow Trusted Platform Module
- play_arrow MACsec
- play_arrow Understanding MACsec
- play_arrow MACsec Examples
-
- play_arrow MAC Limiting and Move Limiting
- play_arrow MAC Limiting and Move Limiting Configurations and Examples
- Understanding MAC Limiting and MAC Move Limiting
- Understanding MAC Limiting on Layer 3 Routing Interfaces
- Understanding and Using Persistent MAC Learning
- Configuring MAC Limiting
- Example: Configuring MAC Limiting
- Verifying That MAC Limiting Is Working Correctly
- Override a MAC Limit Applied to All Interfaces
- Configuring MAC Move Limiting (ELS)
- Verifying That MAC Move Limiting Is Working Correctly
- Verifying That the Port Error Disable Setting Is Working Correctly
-
- play_arrow IP Source Guard
- play_arrow Understanding IP Source Guard
- play_arrow IP Source Guard Examples
- Example: Configuring IP Source Guard on a Data VLAN That Shares an Interface with a Voice VLAN
- Example: Configuring IP Source Guard with Other EX Series Switch Features to Mitigate Address-Spoofing Attacks on Untrusted Access Interfaces
- Example: Configuring IP Source Guard and Dynamic ARP Inspection to Protect the Switch from IP Spoofing and ARP Spoofing
- Example: Configuring IPv6 Source Guard and Neighbor Discovery Inspection to Protect a Switch from IPv6 Address Spoofing
- Configuring IP Source Guard to Mitigate the Effects of Source IP Address Spoofing and Source MAC Address Spoofing
- Example: Configuring IP Source Guard and Dynamic ARP Inspection on a Specified Bridge Domain to Protect the Devices Against Attacks
- Example: Configuring IPv6 Source Guard and Neighbor Discovery Inspection to Protect a Switch from IPv6 Address Spoofing
-
- play_arrow IPv6 Access Security
- play_arrow Neighbor Discovery Protocol
- play_arrow SLAAC Snooping
- play_arrow Router Advertisement Guard
-
- play_arrow Control Plane Distributed Denial-of-Service (DDoS) Protection and Flow Detection
- play_arrow Control Plane DDoS Protection
- play_arrow Flow Detection and Culprit Flows
-
- play_arrow Unicast Forwarding
- play_arrow Unicast Reverse Path Forwarding
- play_arrow Unknown Unicast Forwarding
-
- play_arrow Storm Control
- play_arrow Malware Protection
- play_arrow Juniper Malware Removal Tool
-
- play_arrow Configuration Statements and Operational Commands
Configuring Static ARP Table Entries For Mapping IP Addresses to MAC Addresses
By default, the device responds to an Address Resolution Protocol (ARP) request only if the destination address of the ARP request is on the local network of the incoming interface. For Fast Ethernet or Gigabit Ethernet interfaces, you can configure static ARP entries that associate the IP addresses of nodes on the same Ethernet subnet with their media access control (MAC) addresses. These static ARP entries enable the device to respond to ARP requests even if the destination address of the ARP request is not local to the incoming Ethernet interface.
Also, unlike dynamically learned ARP entries, static ARP entries do not age out. You can also configure static ARP entries in a troubleshooting situation or if your device is unable to learn a MAC address dynamically.
By default, an ARP policer is installed that is shared
among all the Ethernet interfaces on which you have configured the family inet statement. By including the arp statement
at the [edit interfaces interface-name unit logical-unit-number family inet policer] hierarchy
level, you can apply a specific ARP-packet policer to an interface.
This feature is not available on EX Series switches.
To configure static ARP entries:
The Junos OS supports the IPv6 static neighbor discovery cache entries, similar to the static ARP entries in IPv4.
