About the Measurement Designer Page

Tasks You Can Perform

You can perform the following tasks on the Measurement Designer page:

• Create a Test. See Create a Test.

• Create a Monitor. See Create a Monitor.

• Specify a name for a Test or a Monitor—You need to add a name for the Test or the Monitor that you are creating.

  If you are creating a Test, click the Sequence Name or click the Edit (pencil) icon next to Sequence Name and enter a name.

  If you are creating a Monitor, click the Monitor Name or click the Edit (pencil) icon next to Monitor Name and enter a name.

  Sequence Name is the placeholder name for a Test and Monitor Name is the placeholder name for a Monitor.

• Add a Step—A Step is a collection of protocol Tasks.

  In Test creation mode, you can add one or more Steps by clicking + Add Step.

  In Monitor creation mode, there can be only one Step, and it is available by default.

• Add a Task—Each Step can include one or more Tasks. You can add multiple Tasks from the Task selector page displayed by default, or by clicking + Add Task. On the Task page, you can configure different parameters and set evaluation criteria.

• Switch between Test and Monitor—You can switch from the Test to the Monitor creation mode by using the Monitor button and vice versa. If you want to switch from the Test creation mode to Monitor creation mode, ensure that you have configured only one Step as a Monitor can only have a single Step with concurrent Tasks. If you have configured more than one Step, the Steps other than the first one will not be moved to the Monitor creation mode. If you want to create a Monitor based on a Step that is not the first Step, you can move the desired Step to the first position and then switch to the Monitor mode.

  The name you configured for Test and Monitor will remain the same when you switch between modes.

  The duration you configured for a Step in Test will be deleted when you switch to the Monitor mode as a Monitor runs indefinitely.

• Manage input variables for Tests—You can manage the input variables you created by clicking the Global icon on the right side of the page. For more information on input variables, see Create Input Variables.

• Configure Test and Monitor settings—You can configure additional settings for a Test and a Monitor. Click the Test Settings (gear) icon or the Monitor Settings (gear) icon to,

  • Specify the wait duration (in seconds)—You can specify the maximum wait duration. After the Test Agent completes a Step, Paragon Automation waits for the Test Agents to configure or download the plugins or for the Test Agents to be ready to run the Steps.

    By default, the Step wait duration is 60 seconds. The Step wait duration has no effect on the Test duration.

    You cannot add maximum wait duration for a Monitor as the Monitor can only contain one Step.

  • (Optional) Specify a short description a the Test or a Monitor.

  • Add Tags—Specify a key-value pair in the key:value format.

    You can configure Tags for a Test or a Monitor in the key:value format to provide additional information about the Test or Monitor you are configuring. A tag is a key-value pair in which the key signifies a category for which you configure a value. The value is an identifier for the category. Examples of key-value pairs are device and device name (edgedevice:acx7000), site and site name (site:bangalore).

• Save a Test as a template—You can save a Test as a template and reuse this template for creating Test instances in a consistent and reproducible manner. Click the Save as Template button on the top-right corner of the page.

  A Save as Test Template page appears asking you to confirm the save operation.

  A message is displayed confirming that the Test template is saved successfully, and the Test template you created is listed on the Test Templates (Inventory > Active Assurance > Test Templates) page. For more information, see About the Test Templates Page.

• Run a Test or a Monitor—You can run a Test or a Monitor. After you configure a Test and a Monitor, click the Run button.

  Note:

  If a Step does not contain any Task, the Run button will be disabled.

  A successful message is displayed confirming that you have successfully run a Test or a Monitor, corresponding measurements are generated and specified configurations are pushed to the Test Agents. Now, you are redirected to the Test-Name (Observability > Active Assurance > Tests > Test-Name) page or the Monitor-Name (Observability > Active Assurance > Monitors > Monitor-Name) page where you can view the Tests or Monitors you run.

• Additionally, you can perform the following tasks from the bottom-left corner of the page:

  • Zoom in—You can click the Zoom in (plus) icon to zoom in the Steps that you are configuring.

  • Zoom out—You click the Zoom out (minus) icon to zoom out the Steps that you are configuring.

  • Maximize—You can click the Fit view (box) icon to fit Steps to the page size.

  • Toggle interactivity—You can click the Toggle interactivity (lock) icon to lock or unlock the Steps.

    When you lock the Toggle interactivity icon, you can drag the Steps anywhere on the Measurement Designer page but you cannot edit the Step.

    When you unlock the Toggle interactivity icon, you cannot drag the Step anywhere on the Measurement Designer page but you can edit the Step.