Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 
ON THIS PAGE
 

Example: Configuring Two Fiber Line Terminations Using IPLCs for Optical Amplification in a Metro Linear Packet Optical Network

For metro linear and metro ring topologies that require either north-south or east-west communications, you can connect two integrated photonic line card (IPLC) base modules together to form a single node with two fiber line terminations. This example shows how to configure the Junos OS to support the IPLC base modules in a Metro linear packet optical configuration for adding and dropping wavelengths to a local optical interface, and for bypassing wavelengths to another IPLC. You can set up and configure an IPLC node with two line-side fiber terminations.

Requirements

This example uses the following hardware and software components:

  • Three PTX3000 Packet Transport Routers running Junos OS Release 15.1F6

  • Four IPLC base modules

  • Compatible 10-Gigabit or 100-Gigabit Ethernet OTN PICs

For complete information on all PTX Series Packet Transport Routers hardware components, see PTX Series Packet Transport Routers.

For complete information on all PTX Series Packet Transport Routers software features, see Junos OS for PTX Series Packet Transport Routers, Release 15.1.

Before you start this procedure, complete the following tasks:

  • Install the IPLCs, FPCs, and PICs in the PTX3000 chassis.

    Best Practice:

    We recommend that you place the two IPLC modules at Node B into the same FPC/PIC slot pair on the PTX3000 chassis. In this example the IPLCs at Node B are located in FPC slots 2 and 3.

  • Make all connections to and from the PICs in the PTX3000 chassis to the Add and Drop ports on front panel of each IPLC node as shown in Figure 1.

  • Connect your fiber pairs to the Line IN and Line OUT ports on the front panel of each IPLC node as shown in Figure 1.

    For simplicity, Figure 1 does not show the optical ILAs between the three IPLC nodes.

  • On Node B, connect the two IPLC modules together using the PT IN and PT OUT ports on the front panel of the IPLC as shown in Figure 1.

  • Be sure to specify wavelength values on each interface as shown in Figure 1. If you must adjust the wavelength values, make sure that you enter a value supported on the IPLC.

Best Practice:

Anytime you need to disconnect or connect the fiber span from the Line IN and Line OUT ports on the IPLC module, we recommend you disable the optical supervisory channel and the erbium-doped fiber amplifiers on the IPLC.

Always refer to the PTX3000 Packet Transport Router Hardware Guide when connecting or disconnecting cables on the IPLC modules. See PTX3000 Packet Transport Router Hardware Guide.

Overview

This examples describes how to configure Junos OS to support IPLC base modules in a Metro linear packet optical deployment. The Add/Drop ports of the IPLC modules are physically connected to interfaces housed in the same PTX3000 chassis.

The IPLC modules provide the combined functionality of a 32-port Reconfigurable Optical Add/Drop Multiplexer (ROADM), optical amplification, optical equalization, and optical channel monitoring on a single card.

Topology

Figure 1: IPLC in Metro Linear Packet Optical DeploymentIPLC in Metro Linear Packet Optical Deployment

This procedure describes how to configure Junos OS for the IPLC modules. This is not a complete configuration and does not include full instructions for configuring the router or the associated line cards. Before you start this procedure, complete the following hardware and software tasks on the PTX 3000 router:

  • Install the IPLCs, associated line cards, and PICs into the PTX3000 chassis so that the hardware configuration matches what is shown in Figure 1. If you need to make changes to the positions of the cards in the chassis, adjust the FPC numbers referenced in Figure 1 and configure them accordingly.

    Best Practice:

    We recommend that you place the two IPLC modules at Node B into the same FPC or PIC slot pair on the PTX3000 chassis. In this example the IPLCs at Node B are located in FPC slots 2 and 3.

  • Configure the associated wavelengths on the interfaces of the PTX3000 by using the following procedure:

    1. Specify the interface to configure.

      For example:

    2. Specify the wavelength value supported on the interface.

    Note:

    Be sure to specify wavelength values on each interface as shown in Figure 1. If you must adjust the wavelength values, make sure that you enter a value supported on the IPLC.

  • Make all connections to and from the PICs in the PTX3000 chassis to the ADD or DROP ports on front panel of each IPLC node as shown in Figure 1.

  • Connect your fiber pairs to the LINE IN and LINE OUT ports on the front panel of each IPLC node as shown in Figure 1.

    For simplicity, Figure 1 does not show the optical inline amplifiers (optical ILAs) between the three IPLC nodes.

  • On Node B, connect the two IPLC modules together using the PT IN and PT OUT ports on the front panel of the IPLC as shown in Figure 1.

This example results in the following configuration:

Table 1: Wavelength, Port, and IPLC Nodes Mapping

Wavelength

Node A

Node B

Node C

Optical Interface Waveform is Switched to on PTX3000 Chassis

IPLC

Slot:

Port:

Mode:

Optical Interface Waveform is Switched to on PTX3000 Chassis

IPLC

Slot:

Port:

Mode:

Optical Interface Waveform is Switched to on PTX3000 Chassis

IPLC

Slot:

Port:

Mode:

1554.54

—

—

et-8/0/4

Slot: 2

Port: 8

Mode: switch

et-10/0/2

Slot: 8

Port: 8

Mode: switch

1556.15

et-12/0/3

Slot: 1

Port: 6

Mode: switch

—

Slot: 2

Port: 6

Mode: wss-express-in(bypass)

Slot: 3

Port: 6

Mode: wss-express-in (bypass)

et-10/0/3

Slot: 8

Port: 6

Mode: switch

1556.96

et-12/0/2

Slot: 1

Port: 5

Mode: switch

et-8/0/3

Slot: 3

Port: 5

Mode: switch

—

—

1560.20

et-12/0/1

Slot: 1

Port: 1

Mode: switch

et-6/0/2

Slot: 2

Port: 1

Mode: switch

Slot: 3

Port: 1

Mode: switch

et-10/0/1

Slot: 8

Port: 1

Mode: switch

1561.01

et-12/0/0

Slot: 1

Port: 0

Mode: switch

et-6/0/1

et-6/0/0

Slot: 2

Port: 0

Mode: switch

Slot: 3

Port: 0

Mode: switch

et-10/0/0

Slot: 8

Port: 0

Mode: switch

  • 3x100G of Ethernet between Node A and Node B through a multi-span link.

  • 3x100G of Ethernet between Node B and Node C through a multi-span link.

  • 1x100G of Ethernet between Node A and Node C through a multi-span link including an optical bypass at through Node B.

  • In this example:

    • Wavelengths 1561.01 and 1560.20 are dropped at Node B and are also reused in both directions (Node A and Node C).

  • Other wavelengths such as wavelength 1556.96 between Node A and Node B and wavelength 1554.54 between Node B and Node C are used in only a single direction.

  • Wavelengths used in both directions can also be configured for optical buypass if it was necessary to reduce the packet throughput between the nodes. You can configure optical bypasses through the CLI, they do not require manual connection.

  • If traffic changes, you could configure Node B with 1561.01 and 1560.20 as optical bypass and that creates an additional 2x100G between Node A and Node C, leaving only 100 Gbps of traffic to Node B (and leaving four interfaces unused).

Configuration

The following example requires you to navigate various levels in the configuration hierarchy.

For information about navigating the CLI, see Using the CLI Editor in Configuration Mode.

Before you start this procedure, be sure to complete the tasks described in the Requirementssection of this example.

To configure the IPLC base modules in this example, perform these tasks:

CLI Quick Configuration

To quickly configure this example, copy the following commands into a text file, remove any line breaks, and then paste the commands into the CLI at the [edit] hierarchy level.

Configuring the IPLC Base Module at Node A

Step-by-Step Procedure

This procedure describes how to configure the IPLC base module in slot 1 of Node A in this example.

Before you start this procedure, be sure to complete the tasks described in the Requirements section of this example.

To configure the IPLC base module in slot 1 of Node A:

  1. From the Junos Space user interface, click the Build icon on the Connectivity Services Director banner.

    The workspaces that are applicable to Build mode are displayed on the Tasks pane.

  2. From the View selector, select Device View.

    The functionalities that you can configure in this view are displayed.

  3. From the Device View pane, click the plus sign (+) next to the My Network tree to expand the tree and select the PTX300 router for which you want to define the optical IPLC settings.

    The network tree is expanded and the selected device is highlighted.

  4. From the Tasks pane, select Device Management > View Physical Inventory.

    An image of the device is displayed on the right pane.

  5. Select an optical IPLC in the image of the device.

    The Component Info dialog box is displayed.

  6. Click the Status/Config tab at the bottom of the dialog box.

    The IPLC Line dialog box is displayed on the right pane with the configuration settings that pertain to the IPLC.

  7. Specify the FPC or PIC slot in which the IPLC base module resides by selecting the slot in the Chassis View.

    In this case, because the IPLC base module resides in FPC slot 1, select the IPLC 1 component in the image of the chassis.

  8. Configure wavelength 1561.01 on port 0 of the IPLC base module to be switched to optical interface et-12/0/0. In the Wavelength Configuration section, select the Show All Wavelengths check box, and beside the 1561.01 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  9. From the end-point column, click in the cell corresponding to the wavelength of 1561.01, and then click the drop-down arrow. From the drop-down menu, select et-12/0/0 to which you want the wavelength of the IPLC base module to be switched.

  10. Configure wavelength 1560.20 on port 1of the IPLC base module to be switched to optical interface et-12/0/1. In the Wavelength Configuration section, beside the 1560.20 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  11. From the end-point column, click in the cell corresponding to the wavelength of 1560.20, and then click the drop-down arrow. From the drop-down menu, select et-12/0/1 to which you want the wavelength of the IPLC base module to be switched.

  12. Configure wavelength 1556.96 on port 5 of the IPLC base module to be switched to optical interface et-12/0/2. In the Wavelength Configuration section, beside the 1556.96 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  13. From the end-point column, click in the cell corresponding to the wavelength of 1556.96, and then click the drop-down arrow. From the drop-down menu, select et-12/0/2 to which you want the wavelength of the IPLC base module to be switched.

  14. Configure wavelength 1556.15 on port 6 of the IPLC base module to be switched to optical interface et-12/0/3. In the Wavelength Configuration section, beside the 1556.15 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  15. From the end-point column, click in the cell corresponding to the wavelength of 1556.15, and then click the drop-down arrow. From the drop-down menu, select et-12/0/3 to which you want the wavelength of the IPLC base module to be switched.

  16. Click Update to save the specified configuration settings.

Configuring the Two IPLC Base Modules at Node B

Step-by-Step Procedure

This procedure describes how to configure the IPLC base module in slot 2 of Node B in this example.

Before you start this procedure, be sure to complete the tasks described in the Requirements section of this example.

Best Practice:

We recommend that you place the two IPLC modules in the same FPC or PIC slot pair on the PTX3000 chassis.

To configure the IPLC base module in slot 2 of Node B:

  1. From the Junos Space user interface, click the Build icon on the Connectivity Services Director banner.

    The workspaces that are applicable to Build mode are displayed on the Tasks pane.

  2. From the View selector, select Device View.

    The functionalities that you can configure in this view are displayed.

  3. From the Device View pane, click the plus sign (+) next to the My Network tree to expand the tree and select the PTX300 router for which you want to define the optical IPLC settings.

    The network tree is expanded and the selected device is highlighted.

  4. From the Tasks pane, select Device Management > View Physical Inventory.

    An image of the device is displayed on the right pane.

  5. Select an optical IPLC in the image of the device.

    The Component Info dialog box is displayed.

  6. Click the Status/Config tab at the bottom of the dialog box.

    The IPLC Line dialog box is displayed on the right pane with the configuration settings that pertain to the IPLC.

  7. Specify the FPC or PIC slot in which the IPLC base module resides by selecting the slot in the Chassis View.

    In this case, because the IPLC base module resides in FPC slot 2, select the IPLC 2 component in the image of the chassis.

  8. Create a logical connection between this IPLC base module and the IPLC base module in slot 3. Select FPC 3 from the Express IPLC list in the Settings/Status section.

  9. Configure wavelength 1561.01 on port 0 of the IPLC base module to be switched to optical interface et-6/0/1. In the Wavelength Configuration section, select the Show All Wavelengths check box, and beside the 1561.01 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  10. From the end-point column, click in the cell corresponding to the wavelength of 1561.01, and then click the drop-down arrow. From the drop-down menu, select et-6/0/1 to which you want the wavelength of the IPLC base module to be switched.

  11. Configure wavelength 1560.20 on port 1of the IPLC base module to be switched to optical interface et-6/0/2. In the Wavelength Configuration section, beside the 1560.20 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  12. From the end-point column, click in the cell corresponding to the wavelength of 1560.20, and then click the drop-down arrow. From the drop-down menu, select et-6/0/2 to which you want the wavelength of the IPLC base module to be switched.

  13. Configure wavelength 1554.54 on port 5 of the IPLC base module to be switched to optical interface et-8/0/4. In the Wavelength Configuration section, beside the 1556.54 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  14. From the end-point column, click in the cell corresponding to the wavelength of 1554.54, and then click the drop-down arrow. From the drop-down menu, select et-8/0/4 to which you want the wavelength of the IPLC base module to be switched.

  15. Configure wavelength 1556.15 on port 6 of the IPLC base module in slot 2 to be bypassed. In the Wavelength Configuration section, beside the 1556.15 row in the wavelength column, select express from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  16. Click Update to save the specified configuration settings.

Step-by-Step Procedure

This procedure describes how to configure the IPLC base module in slot 3 of Node B in this example.

Before you start this procedure, be sure to complete the tasks described in the Requirements section of this example.

To configure the IPLC base module in slot 3 of Node B:

  1. From the Junos Space user interface, click the Build icon on the Connectivity Services Director banner.

    The workspaces that are applicable to Build mode are displayed on the Tasks pane.

  2. From the View selector, select Device View.

    The functionalities that you can configure in this view are displayed.

  3. From the Device View pane, click the plus sign (+) next to the My Network tree to expand the tree and select the PTX300 router for which you want to define the optical IPLC settings.

    The network tree is expanded and the selected device is highlighted.

  4. From the Tasks pane, select Device Management > View Physical Inventory.

    An image of the device is displayed on the right pane.

  5. Select an optical IPLC in the image of the device.

    The Component Info dialog box is displayed.

  6. Click the Status/Config tab at the bottom of the dialog box.

    The IPLC Line dialog box is displayed on the right pane with the configuration settings that pertain to the IPLC.

  7. Specify the FPC or PIC slot in which the IPLC base module resides by selecting the slot in the Chassis View.

    In this case, because the IPLC base module resides in FPC slot 3, select the IPLC 3 component in the image of the chassis.

  8. Create a logical connection between this IPLC base module and the IPLC base module in slot 2. Select FPC 2 from the Express IPLC list in the Settings/Status section.

  9. Configure wavelength 1561.01 on port 0 of the IPLC base module to be switched to optical interface et-6/0/0. In the Wavelength Configuration section, select the Show All Wavelengths check box, and beside the 1561.01 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  10. From the end-point column, click in the cell corresponding to the wavelength of 1561.01, and then click the drop-down arrow. From the drop-down menu, select et-6/0/0 to which you want the wavelength of the IPLC base module to be switched.

  11. Configure wavelength 1560.20 on port 0 of the IPLC base module to be switched to optical interface et-8/0/2. In the Wavelength Configuration section, beside the 1560.20 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  12. From the end-point column, click in the cell corresponding to the wavelength of 1561.01, and then click the drop-down arrow. From the drop-down menu, select et-8/0/2 to which you want the wavelength of the IPLC base module to be switched.

  13. Configure wavelength 1556.96 on port 5 of the IPLC base module to be switched to optical interface et-8/0/3. In the Wavelength Configuration section, beside the 1560.20 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  14. From the end-point column, click in the cell corresponding to the wavelength of 1556.96, and then click the drop-down arrow. From the drop-down menu, select et-8/0/3 to which you want the wavelength of the IPLC base module to be switched.

  15. Configure wavelength 1556.15 on port 6 of the IPLC base module in slot 3 to be bypassed. In the Wavelength Configuration section, select the Show All Wavelengths check box, and beside the 1560.20 row in the wavelength column, select express from the drop-down menu in the configuration column of the table for the corresponding wavelength.

  16. Click Update to save the configured settings.

Configuring the IPLC Base Module at Node C

Step-by-Step Procedure

This procedure describes how to configure the IPLC base module in slot 8 of Node C in this example.

Before you start this procedure, be sure to complete the tasks described in the Requirements section of this example.

Step-by-Step Procedure

To configure the IPLC base module in slot 8 of Node C:

  1. From the Junos Space user interface, click the Build icon on the Connectivity Services Director banner.

    The workspaces that are applicable to Build mode are displayed on the Tasks pane.

  2. From the View selector, select Device View.

    The functionalities that you can configure in this view are displayed.

  3. From the Device View pane, click the plus sign (+) next to the My Network tree to expand the tree and select the PTX300 router for which you want to define the optical IPLC settings.

    The network tree is expanded and the selected device is highlighted.

  4. From the Tasks pane, select Device Management > View Physical Inventory.

    An image of the device is displayed on the right pane.

  5. Select an optical IPLC in the image of the device.

    The Component Info dialog box is displayed.

  6. Click the Status/Config tab at the bottom of the dialog box.

    The IPLC Line dialog box is displayed on the right pane with the configuration settings that pertain to the IPLC.

  7. Specify the FPC or PIC slot in which the IPLC base module resides by selecting the slot in the Chassis View.

    In this case, because the IPLC base module resides in FPC slot 8, select the IPLC 8 component in the image of the chassis.

  8. Configure wavelength 1561.01 on port 0 of the IPLC base module to be switched to optical interface et-10/0/0. In the Wavelength Configuration section, select the Show All Wavelengths check box, and beside the 1561.01 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

    From the end-point column, click in the cell corresponding to the wavelength of 1561.01, and then click the drop-down arrow. From the drop-down menu, select et-10/0/0 to which you want the wavelength of the IPLC base module to be switched.

  9. Configure wavelength 1560.20 on port 1 of the IPLC base module to be switched to optical interface et-10/0/1. In the Wavelength Configuration section, beside the 1560.20 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

    From the end-point column, click in the cell corresponding to the wavelength of 1560.20, and then click the drop-down arrow. From the drop-down menu, select et-10/0/1 to which you want the wavelength of the IPLC base module to be switched.

  10. Configure wavelength 1554.54 on port 8 of the IPLC base module to be switched to optical interface et-10/0/2. In the Wavelength Configuration section, beside the 1554.54 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

    From the end-point column, click in the cell corresponding to the wavelength of 1554.54, and then click the drop-down arrow. From the drop-down menu, select et-10/0/2 to which you want the wavelength of the IPLC base module to be switched.

  11. Configure wavelength 1556.15 on port 6 of the IPLC base module to be switched to optical interface et-10/0/3. In the Wavelength Configuration section, beside the 1556.15 row in the wavelength column, select switch from the drop-down menu in the configuration column of the table for the corresponding wavelength.

    From the end-point column, click in the cell corresponding to the wavelength of 1556.15, and then click the drop-down arrow. From the drop-down menu, select et-10/0/3 to which you want the wavelength of the IPLC base module to be switched.

  12. Click Update to save the configured settings.

Results

Verification

Confirm that the configuration is working properly.

Verifying the Topology of Each IPLC Node

Purpose

Verify the topology of each IPLC node.

Action

Run the show chassis fpc optical-properties topology command with the detail output level at each IPLC node and verify that the following fields match the values listed in Table 1.

  • Port/Wavelength—Verify that this field lists the proper wavelength values and IPLC port numbers for each node in this example.

  • State—Verify that the values for this field match what is listed in Table 1 for the mode value of each IPLC port for each node in this example.

  • Connected To—If the wavelength is being switched, verify that this field lists the correct interface the wavelength is being switched to.

Verify the topology of each IPLC node.

  1. For example, at IPLC Node A, enter the following.

  2. At Node B, enter the following:

  3. At Node C:

Meaning

For example, in Step 1for Node A, you can see that the IPLC module in slot 1 includes the following configuration:

  • Wavelength 1561.01 is switched to optical interface et-12/0/0

  • Wavelength 1560.20 is switched to optical interface et-12/0/1

  • Wavelength 1556.96 is switched to optical interface et-12/0/2

  • Wavelength 1556.16 is switched to optical interface et-12/0/3

This matches what is listed in Table 1 for Node A and confirms the configuration is operating correctly.

Related Documentation