show interfaces smart-sfp-statistics

Physical interface

Name of the physical interface.

Enabled

State of the interface.

Interface index

Index number of the physical interface, which reflects its initialization sequence.

SNMP ifIndex

SNMP index number for the physical interface.

Link-level type

Encapsulation being used on the physical interface.

MTU

Maximum transmission unit size on the physical interface.

Clocking

Reference clock source.

Speed

Speed at which the interface is running.

Duplex

Duplex mode of the interface, either Full-Duplex or Half-Duplex.

MAC-REWRITE Error

Specifies if the encapsulation of the packet has been changed.

BPDU Error

Specifies if a BPDU has been received on a blocked interface.

Loopback

Loopback status: Enabled or Disabled. If loopback is enabled, type of loopback: Local or Remote.

Source filtering

Source filtering status: Enabled or Disabled.

Flow control

Flow control status: Enabled or Disabled. This field is only displayed if asymmetric flow control is not configured.

Device flags

Information about the physical device.

Interface flags

Information about the interface.

Smart Transceiver Type

Type of smart SFP transceiver. Possible values: E1, T1, DS3, STM1, STM4, or STM16.

Smart SFP

Configurable Type. You can configure these Smart SFP transceivers unlike other Smart SFP transceivers which you cannot configure.

Loopback

Specifies if loopback is configured.

Encapsulation Circuit Id

Emulation circuit id for encapulsation. Possible values: 0 through 1048575.

Decapsulation Circuit Id

Emulation circuit id for decapsulation. Possible values: 0 through 1048575.

Mode

Framing mode. Possible values: MEF8 or MPLS.

Dest MAC

Destination MAC address.

TDM defects

Legacy TDM defects. Defects specific to PDH and SDH legacy error codes and defects.

System defects

Smart SFP device defects. Defects are specific to the Smart SFP you use.

CoS queues

Number of CoS queues configured.

Hold-Times

Current interface hold-time up and hold-time down, in milliseconds.

Current address

Configured MAC address.

Hardware address

Hardware MAC address.

Last flapped

Date, time, and how long ago the interface went from down to up. The format is Last flapped: year-month-day hour:minute:second:timezone (hour:minute:second ago). For example, Last flapped: 2008–01–16 10:52:40 UTC (3d 22:58 ago).

Statistics last cleared

Date, time, and how long ago the statistics for the interface were cleared. The format is Statistics last cleared: year-month-day hour:minute:second:timezone (hour:minute:second ago). For example, 2010-05-17 07:51:28 PDT (00:04:33 ago).

Traffic statistics

Number and rate of bytes and packets received and transmitted on the physical interface.

• Input bytes—Number of bytes received on the interface.

• Output bytes—Number of bytes transmitted on the interface.

• Input packets—Number of packets received on the interface.

• Output packets—Number of packets transmitted on the interface.

IPv6 transit statistics

If IPv6 statistics tracking is enabled, number of IPv6 bytes and packets received and transmitted on the logical interface:

• Input bytes—Number of bytes received on the interface.

• Output bytes—Number of bytes transmitted on the interface.

• Input packets—Number of packets received on the interface.

• Output packets—Number of packets transmitted on the interface.

Input errors

Input errors on the interface. The following paragraphs explain the counters whose meaning might not be obvious:

• Errors—Sum of the incoming frame terminates and FCS errors.

• Drops—Number of packets dropped by the input queue of the I/O Manager ASIC. If the interface is saturated, this number increments once for every packet that is dropped by the ASIC's RED mechanism.

• Framing errors—Number of packets received with an invalid frame checksum (FCS).

• Runts—Number of frames received that are smaller than the runt threshold.

• Policed discards—Number of frames that the incoming packet match code discarded because they were not recognized or not of interest. Usually, this field reports protocols that Junos OS does not handle.

• L3 incompletes—Number of incoming packets discarded because they failed Layer 3 sanity checks of the header. For example, a frame with less than 20 bytes of available IP header is discarded. L3 incomplete errors can be ignored if you configure the ignore-l3-incompletes statement.

• L2 channel errors—Number of times the software did not find a valid logical interface for an incoming frame.

• L2 mismatch timeouts—Number of malformed or short packets that caused the incoming packet handler to discard the frame as unreadable.

• FIFO errors—Number of FIFO errors in the receive direction that are reported by the ASIC on the PIC. If this value is ever nonzero, the PIC is probably malfunctioning.

• Resource errors—Sum of transmit drops.

Output errors

Output errors on the interface. The following paragraphs explain the counters whose meaning might not be obvious:

• Carrier transitions—Number of times the interface has gone from down to up. This number does not normally increment quickly, increasing only when the cable is unplugged, the far-end system is powered down and then up, or another problem occurs. If the number of carrier transitions increments quickly (perhaps once every 10 seconds), the cable, the far-end system, or the PIC or PIM is malfunctioning.

• Errors—Sum of the outgoing frame terminates and FCS errors.

• Drops—Number of packets dropped by the output queue of the I/O Manager ASIC. If the interface is saturated, this number increments once for every packet that is dropped by the ASIC's RED mechanism.

• Collisions—Number of Ethernet collisions. The Gigabit Ethernet PIC supports only full-duplex operation, so for Gigabit Ethernet PICs, this number should always remain 0. If it is nonzero, there is a software bug.

• Aged packets—Number of packets that remained in shared packet SDRAM so long that the system automatically purged them. The value in this field should never increment. If it does, it is most likely a software bug or possibly malfunctioning hardware.

• FIFO errors—Number of FIFO errors in the send direction as reported by the ASIC on the PIC. If this value is ever nonzero, the PIC is probably malfunctioning.

• HS link CRC errors—Number of errors on the high-speed links between the ASICs responsible for handling the fabric interfaces.

• MTU errors—Number of packets whose size exceeded the MTU of the interface.

• Resource errors—Sum of transmit drops.

Egress queues

Total number of egress queues supported on the specified interface.

Queue counters

CoS queue number and its associated user-configured forwarding class name.

• Queued packets—Number of queued packets.

• Transmitted packets—Number of transmitted packets.

• Dropped packets—Number of packets dropped by the ASIC's RED mechanism.

Input rate

Input rate in bits per second (bps) and packets per second (pps).

Output rate

Output rate in bps and pps.

Logical interface

Name of the logical interface.

Index

Index number of the logical interface, which reflects its initialization sequence.

SNMP ifIndex

SNMP interface index number for the logical interface.

Flags

Information about the logical interface.

If unicast Reverse Path Forwarding (uRPF) is explicitly configured on the specified interface, the uRPF flag appears. If uRPF was configured on a different interface (and therefore is enabled on all switch interfaces) but was not explicitly configured on the specified interface, the uRPF flag does not appear even though uRPF is enabled.

Input packets

Number of packets received on the interface.

Output packets

Number of packets transmitted on the interface.

Encapsulation

Encapsulation method used on the logical interface.

• Input packets—Number of packets received on the interface.

• Output packets—Number of packets transmitted on the interface.

Traffic statistics

Number and rate of bytes and packets received and transmitted on the physical interface.

• Input bytes—Number of bytes received on the interface.

• Output bytes—Number of bytes transmitted on the interface.

• Input packets—Number of packets received on the interface.

• Output packets—Number of packets transmitted on the interface.

Local statistics

• Input bytes—Number of bytes received on the interface.

• Output bytes—Number of bytes transmitted on the interface.

• Input packets—Number of packets received on the interface.

• Output packets—Number of packets transmitted on the interface.

Transit statistics

• Input bytes—Number of bytes received on the interface.

• Output bytes—Number of bytes transmitted on the interface.

• Input packets—Number of packets received on the interface.

• Output packets—Number of packets transmitted on the interface.

Addresses, Flags

Information about the address flags.

protocol-family

Protocol family configured on the logical interface. If the protocol is inet, the IP address of the interface is also displayed.

MTU

Maximum transmission unit size on the physical interface.

Destination

IP address of the remote side of the connection.

Local

IP address of the logical interface.

Broadcast

Broadcast address of the logical interlace.

Generation

Unique number for use by Juniper Networks technical support only.

Route table

Route table in which the logical interface address is located. For example, 0 refers to the routing table inet.0.